BFT THALIA BT A80 Instrucciones De Instalación página 47

Parameter min. max.
15
CL SPEED
15
SLOW SPEED
0
aintenance
(*) In the European Union, apply standard EN 12453 for force limitations, and standard EN 12445 for measuring method.
(**) Impact forces can be reduced by using deformable edges.
TABLE "B" - LOGIC MENU - (logic)
Logic Definition
Motor type
(Set the type of motor
OTOR TYPE
connected to the
Automatic Closing
TCA
Power Down
Psave
activation
Activates ULink
ULINK 1
Fast closing
FAST CLS.
STEP-BY-STEP Step-by-step
movement
OVE NT
Pre-alarm
PRE-ALAR
INSTALLATION MANUAL
Default Personal
100 100
100 25
Slow-down speed [%]
Programming number of
operations for maintenance
250 0
Cross out
Default setting
used
0
1
2
3
4
5
6
7
8
0
9
board).
10
11
12
13
14
15
16
17
0
1
0
Time
2
0
1
1
0
0
Protocol
1
0
0
1
0
1
0
2
0
0
1-10
Definition
Percentage of maximum speed that can be reached by motor(s) during closing.
WARNING: Once the parameter has been edited, a complete uninterrupted
Closing speed [%]
opening-closing cycle is required. WARNING: when the display reads "SET",
obstacle detection is not active.
Opening and closing speed of motor(s) during slow-down stage, given as a percentage
of maximum running speed. WARNING: Once the parameter has been edited, a
complete uninterrupted opening-closing cycle is required. WARNING: When the
display reads ""SET"", obstacle detection is not active.
ATTENTION: for motor type ELI BT A35 it is not possible to exclude the deceler-
ation; values greater than 50% will be considered at 50%.
Allows you to set a number of operations after which the need for maintenance
will be reported on the AUX output configured as Maintenance or Flashing
threshold
Light and Maintenance .
[in hundreds]
Motors not active
NOT MANAGED
NOT MANAGED
IGEA BT
NOT MANAGED
NOT MANAGED
SUB BT
KUSTOS BT A - PHOBOS BT A - PHOBOS N BT
GIUNO ULTRA BT A 20 - GIUNO ULTRA BT A50
VIRGO SMART BT A - 5 wires
VIRGO SMART BT A - 3 wires
E5 BT A18
E5 BT A12
ELI BT A40 + FCE
ELI BT A35 V + FCE
ELI BT A40
ELI BT A35
PHOBOS VELOCE BT B35
Logic not enabled
Switches automatic closing on
It activates automatic closure also after a reversal due to an obstacle when closing. In case of a reversal
during opening, it retries opening after 2 seconds; if it finds an obstacle during opening 4 consecutive
times, it closes.
Configuration can only be activated with the E5 BT A12 motor (motor type 12).
The logic can only be used with pedestrian doors the energy of which is limited to within 1.69J.
Power Down DEACTIVATED, i.e. the power supply of the accessories is always present.
Power Down ACTIVE, i.e. the power supply of the accessories is deactivated with the gate stopped.
Both U-Link connectors support the new U-Link2.0 protocol.
Enabling of the U-Link protocol (previous version) on the optional card connector 1. The previous
version of the U-Link protocol can be activated on connector 1.
Logic not enabled
Closes 3 seconds after the photocells are cleared before waiting for the set TCA to elapse.
Inputs configured as Start
E, Start I, Ped operate with
4-step logic.
Inputs configured as Start
E, Start I, Ped operate
with 3-step logic. Pulse
during closing reverses
DURING CLOSING
movement.
Inputs configured as Start
E, Start I, Ped operate with
DURING OPENING
2-step logic. Movement
reverses with each pulse.
AFTER STOP
The flashing light comes on at the same time as the motor(s) starts.
The pre-alarm function is activated: The flashing light comes on before the motor(s) starts.
The value of the parameter indicates the duration of the pre-flashing in seconds.
Description
Optional extras
step-by-step mov.
2 STEP 3 STEP
CLOSED
OPENS OPENS
OPEN
CLOSES
CLOSES
STOP + TCA
OPENS OPENS
4 STEP
OPENS
STOPS
CLOSES
STOP + TCA
OPENS
47
THALIA BT A80 -