Idiomas disponibles
Idiomas disponibles
Introduction (GB)
Congratulations on purchasing this high-quality Car Audio Amplifier. The
development work invested in the new Velocity Amplifier offers you
complete music enjoyment in your car. Our Velocity Amplifiers are fitted
with all typical product features expected from a high-end amplifier, but
also contain a number of technical highlights as well, such as:
• 2 ohm stability (only in stereo mode) for low-ohm amplifier systems
with high performance
• Variable frequency dividers for high and low pass setting
• Variable input voltage 0.3 - 8 V
• Transistors for power supply using MOSPET technology
• Gold-plated screw connectors for loudspeaker and power supply
• Preamp-Out and -In gold-plated
• Sub Sonic Filter
• Bass-Boost
To achieve the best possible sound quality from your new Velocity
Amplifier we recommend that it is installed by an authorised Velocity
dealer and that the matching Velocity Loudspeaker system is used. This
is the way to obtain the full enjoyment of the performance of your
amplifier.
Let us finally mention the aspect of health safety. Please remember when
listening to music in your car that constant sound-pressure levels of more
than 100 dB can cause permanent damage to the human ear right up to
complete loss of hearing. Sound-pressure levels of more than 130 dB
can be achieved with modern high-performance systems and high-
quality loudspeaker configurations.
You can also obtain further information on our Velocity Series at our
Internet address http://www.velocity.de
Safety instructions
Rules to be observed in fitting and connection
Disconnect the negative pole of the car battery for the duration of the
installation and connection works.
The safety instructions of the car manufacturer (airbag, alarm systems,
on-board computers, engine immobilizers) must be observed.
With regard to accident prevention the Velocity power amplifier must be
affixed in a professional manner. The mounting surface must be suitable
for accepting the enclosed screws and must offer secure installation.
When drilling holes please ensure that no car components are damaged
(battery, cables, fuse box).
The amplifier should be installed at a suitable location, i.e. under the
seats or in the boot, Fig. 1.
A dry position should be selected for the installation location that
guarantees sufficient air circulation for the cooling of the amplifier.
Use cable bushings at sharp-edged holes.
Use loudspeakers with 2-4 ohm impedance. Pay attention to the max.
loading (music output).
Use 16 mm
2
loudspeaker connection cables. Do not connect the
loudspeakers to earth, use only the designated terminals.
The cross-section of the positive and negative cable may not be less than
2
16 mm
.
Fit a fuse holder to the positive cable between the battery and the
amplifier directly at the battery.!
Velocity ReferenceAmplifier VR 502/1002
The amplifier is suitable for connecting to car radios with cinch connector.
Use the Blaupunkt ISO-Cinch Adapter for connecting to car radios with
ISO connector.
Possibilities for use and switching:
VR 502
Max Power
2x100 / 1x300 Watt Fig. 5
4 Ohm
Max Power
2x150 / 1x400 Watt Fig. 5
2 Ohm
RMS Power
2x50 / 1x150 W
4 Ohm
(THD @ 0.05 %)
RMS Power
2x75 / 1x200 W
2 Ohm
(THD @ 0.05 %)
Freq. response
10 Hz - 70.000 Hz
- 3 dB
Signal-to-Noise
> 95 dB
Ratio
Input Level
0,3 - 8 V
High Pass
40 - 250 Hz
Low Pass
40 - 120 Hz
Bass Boost
+10 dB (45 Hz)
Dimensions
WxHxD (mm)
382 x 70 x 290
Tri-Mode
Allows you to drive two loudspeakers and to connect a third speaker
in mono operation (bridged mode) , Fig. 6.
Positive/negative connections
We recommend a minimum cross-section of 16 mm
available positive cable to the battery and connect using fuse holder. The
fuse holder should be connected close to the battery.
Use cable bushings at sharp-edged holes. Screw the commercially
available negative cable firmly to an interference-free earthing-point (car
body bolt, car body sheet, but not to the negative battery pole). Scrape
the contact surface of the earthing point until it is blank metal and coat
with graphite grease.
Connection examples:
Connection of power supply ........................................................ Fig. 2
Connection of car radio with cinch output ................................... Fig. 3
Connection of car radio with loudspeaker output ........................ Fig. 4
Loudspeaker connections ........................................................... Fig. 5
Tri - Mode ..................................................................................... Fig. 6
When connecting via the cinch or loudspeaker sockets of the car radio
the switch cable must be connected.
Controller (GAIN)
Using the Gain Controller you can adjust the input sensitivity of the
Velocity Power Amplifier to the output voltage of your car radio pre-
amplifier output.
The adjusting range is from 0.3 V to 8 V.
When connecting a car radio from other manufacturers the input sensitivity
should be adapted in accordance with the specifications of the
manufacturer.
Please note that the Gain Adjust Controller is not designed for volume
adjustment!
Preamp-INPUT
Please use high-quality Velocity cinch/RCA cables for connecting the
pre-amp input for right and left channels.
Preamp-OUTPUT
Output for hook-up of an additional amp (for cascaded amplifiers).
To make this connection, please use high-quality Velocity Cinch/RCA
cables as well.
3
VR1002
2x200 / 1x600 Watt
2x300 / 1x1000 Watt
Fig. 5
2x100 / 1x300 Watt
(THD @ 0.05 %)
Fig. 5
2x150 / 1x500 Watt
(THD @ 0,05 %)
10 Hz - 70.000 Hz
> 95 dB
0,3 - 8 V
40 - 250 Hz
40 - 120 Hz
+10 dB (45 Hz)
482 x 72 x 290
2
. Lay commercially
+12V
8 622 402 984
