Idiomas disponibles
Idiomas disponibles
torque is greater when the torque adjustment ring is set on a higher
setting. The torque is less when the torque adjustment ring is set on
a lower setting.
Make the setting as follows:
1 - 4
for driving small screws
5 - 9
for driving screws into soft material
10 - 14
for driving screws into soft and hard material
15 - 21
for driving screws into hard wood
22
for driving larger screws
for heavy drilling
for drilling in masonry and concrete
7. USING THE LED LIGHT
To turn on the light simply press the on/off switch. When you
release the on/off switch, the light will be off. LED lighting
increases visibility-great for dark or enclosed area. LED is also a
battery capacity indicator. It will flash when power gets low.
8. BATTERY CAPACITY INDICATOR
Your tool is equipped with battery capacity indicator. Press the
on/off switch halfway or fully, the battery capacity indicator will
light up to show the amount of charge left in the battery.
Fuel Gauge
3 lights
2 lights
1 light
9. USING BELT CLIP (SEE FIG. J)
Screw the Belt clip on the tool with the screw . The Belt clip can be
hooked on your belt or pocket, etc.
10. DRILLING
When drilling into a hard smooth surface, use a center punch
to mark the desired hole location. This will prevent the drill bit
from slipping off center as the hole is started. Hold the tool firmly
and place the tip of the bit at the point to be drilled. Depress
the switch trigger to start the tool. Move the drill bit into the
workpiece, applying only enough pressure to keep the bit cutting.
Do not force or apply side pressure to elongate a hole.
WARNING: Tungsten carbide drill bits should
always be used for concrete and masonry.
When drilling in metal, only use HSS drill bits
in good condition. Always use a magnetic bit holder
(not included) when using short screwdriver bits.
When screw-driving, apply a small quantity of liquid
soap or similar to the screw threads to ease
insertion.
11. OVERLOAD PROTECTION
When overloaded, the motor comes to a stop. Relieve the load on
the machine immediately and allow cooling for approx. 30 seconds
at the highest no-load speed.
EN
12. TEMPERATURE DEPENDENT OVERLOAD
PROTECTION
When using as intended for the power tool cannot be subject
to overload. When the load is too high or the allowable battery
temperature of 75°C is exceeded, the electronic control switches off
the power tool until the temperature is in the optimum temperature
range again.
13. PROTECTION AGAINST DEEP DISCHARGING
The Li-ion battery is protected against deep discharging by the
"Discharging Protection System". When the battery is empty,
the machine is switched off by means of a protective circuit: The
inserted tool no longer rotates.
PROBLEM SOLUTION
1. WHY DOES THE DRILL NOT TURN ON WHEN
YOU PRESS THE SWITCH?
The forward/reverse rotation control, which is on top of the trigger,
is positioned in the lock function. Unlock the forward/reverse
rotation control by putting it into the required rotation position. Push
the trigger and the drill will start to rotate.
2. THE DRILL STOPS BEFORE THE SCREW IS
COMPLETELY TIGHTENED. WHY?
Verify the torque position of the torque adjusting ring, you can find
the torque-adjusting ring between the chuck and the drill body.
Position 1 is the lowest torque (screw driving force) and position
Capacity
22 is the highest torque (screw driving force). Position is for drill
operation. Position
> 70%
torque adjusting ring to a higher position to reach the best result.
40%~70%
3. REASONS FOR DIFFERENT BATTERY PACK
< 40%
WORKING TIMES
Charging time problems and having not used a battery pack for
a prolonged time will reduce the battery pack working time. This
can be corrected after several charge and discharge operations by
charging & working with your drill. Heavy working conditions such
as large screws into hard wood will use up the battery pack energy
faster than lighter working conditions. Do not re-charge your battery
pack below 0
MAINTENANCE
Remove the battery pack from the tool before
carrying out any adjustment, servicing or
maintenance.
Your tool requires no additional lubrication or maintenance.
There are no user serviceable parts in your power tool. Never use
water or chemical cleaners to clean your power tool. Wipe clean
with a dry cloth. Always store your power tool in a dry place. Keep
the motor ventilation slots clean. Keep all working controls free of
dust. Occasionally you may see sparks through the ventilation slots.
This is normal and will not damage your power tool.
For Battery tools
The ambient temperature range for the use and storage of tool and
battery is 0
The recommended ambient temperature range for the charging
system during charging is 0
is for hammer drill operation. Regulate the
C and above 40
C as this will affect performance.
o
o
C-45
C.
o
o
C-40
C.
o
o
17
