Tabla de contenido
Idiomas disponibles
Idiomas disponibles
English
3. Give the nozzle a firm tug after the quick connect collar
has locked into place to ensure the nozzle is locked
into place.
Spray Tip
Application
40 ° White Nozzle
For gentle wide area cleaning.
Black Turbo Nozzle For abrasive cleaning.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Proper Hand Position (Fig. F)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the spray handle
grip
5
and the other hand on the spray handle
Test Ground‑Fault Circuit‑Interrupter
(GFCI) Before Each Use (Fig. A)
This pressure washer is provided with a ground‑fault
circuit‑interrupter (GFCI) built into the plug of the
power‑supply cord. This device provides additional
protection from the risk of electric shock.
1. Plug the Ground Fault Circuit Interrupter (GFCI)
working grounded outlet.
2. The indicator at the top of the GFCI should turn green
when product is ready to use.
3. Press the "TEST" button (bottom). The green indicator
should disappear.
4. Press "RESET" button for use.
5. Do not use the pressure washer if the above test fails.
Pressure Washing
Preparing Surface for Cleaning
•
Remove objects from the area which could create a
hazard such as children's toys or outdoor furniture.
•
Insure that all doors and windows are closed tight.
•
Protect all plants and trees in the adjacent area with a
drop cloth ensuring that they will not be harmed by
any overspray.
•
Pre‑rinse cleaning area with fresh water.
•
Use only detergents formulated for pressure washers.
•
Always test detergent in an inconspicuous area
before use.
6
Preparing Pressure Washer Unit for Use
1. Connect the water supply to the pressure washer. For
instructions on connecting the water supply to the
pressure washer, please refer to Attaching garden hose
under Assembly and Adjustments.
2. Connect the high pressure hose to the pressure washer
and the pressure wand. For instructions on connecting
the high pressure hose to the pressure washer and
pressure wand, please refer to Attaching high Pressure
hose under Assembly and Adjustments.
Preparing Spray Handle (Fig. A)
iMPORTAnT: Before turning on the pressure washer unit,
disengage the trigger lock‑off
1. Disengage the trigger lock‑off
2. Squeeze the trigger
4
.
purge the system of air.
3. If air is still found in the water stream, continue to run
water through the spray handle.
Cleaning a Surface (Fig. A)
1. To start the pressure washer, press the ON button
2. The best angle for spraying water against a cleaning
surface is 45 °.
‑
16
into a
‑
3. To disengage the spray handle, release the trigger.
nOTE: Excessive pump pressure may be the result of
a clogged nozzle or brass coupling. Always turn OFF
the pressure washer unit and unplug the unit before
attempting to unclog a nozzle or brass coupler.
Moving the Pressure Washer (Fig. A)
1. Turn OFF the pressure washer unit
button
2. Point the spray wand
trigger
3. When the spray wand is completely empty, lift the
pressure washer by the handle
Shutdown (Fig. A, D)
1. Turn OFF the pressure washer unit
button
2. Turn OFF water at the faucet.
3. Discharge residual pressure by squeezing the trigger
until no more water comes out of the spray wand
4. Engage the spray trigger lock‑off
DANGER: Risk of fluid injection and laceration.
When using the high pressure setting, DO NOT allow
the high pressure spray to come in contact with
unprotected skin, eyes, or with any pets or animals.
Serious injury will occur.
CAUTION: Before operation:
6
and squeeze the trigger
7
. Hold the trigger for 30 seconds to
Spraying head on tends to cause dirt particles to
imbed in the surface.
When working on vertical surfaces, it is best to
apply detergent starting at the bottom and working
upwards which will prevent the detergent from
sliding down and causing streaks.
10
and then turn OFF the water supply.
2
in a safe direction and pull the
7
to release remaining water pressure.
10
and unplug the cord from the outlet.
7
.
6
.
9
.
8
by pressing the OFF
11
.
8
by pressing the OFF
7
2
.
6
.
Tabla de contenido
