Shutting Down; Grey Intelligent Key; Transport Run - Kärcher B 95 RS Manual De Instrucciones

 Confirm the changed setting by press-
ing the Info button or wait till the set val-
ue is automatically accepted after 10
seconds.
Setting the Vacuum Bar
Oblique position
To improve the vacuuming result on tiled
floors the vacuum bar can be turned to an
oblique position of up to 5°.
 Release the wing nuts.
 Turn the vacuum bar.
 Tighten the wing nuts.
Inclination
If the vacuum result is unsatisfactory the in-
clination of the straight vacuum bar can be
modified.
 Loosen both clamping levers.
 Adjust the inclination of the suction bar.
 Tighten both clamping levers.
Emptying the waste Water tank
Note:
Overflow waste water tank. When the
wastewater tank is full, the suction turbine
switches off and "Waste water tank full" is
shown on the display.
WARNING
Please observe the local provisions regard-
ing the wastewater treatment.
 Take the dirt water discharge hose from
the support and lower above a suited
collection device.
Note:
The wastewater flow can be controlled by
squeezing the dosing unit.
22
 Let off water by opening the dosage de-
vice at the discharge hose.
 The rinse the dirt water reservoir with
clear water.
 Press the wastewater hose into the
holder on the appliance.
Emptying the Fresh Water Tank
 Open the lock of the fresh water reser-
voir.
 Drain the fresh water.
 Attach the closure of the fresh water
tank.
Empty waste container (only with R
cleaning head)
 Check the waste container. If needed,
remove and empty waste container af-
ter work.

Shutting down

 Remove the Intelligent Key.
 Secure the machine with wheel chocks
to prevent it from rolling away.
 Charge battery, if required.

Grey Intelligent Key

 Plug in the Intelligent Key.
 Select the desired function by turning
the Info button.
The different functions are described in the
following.

Transport run

 Turn programme selector switch to
"transport run".
 Press Info button.
In the transport run menu the following set-
tings can be made:
Key management
In this menu item the authorisations for yel-
low intelligent keys as well as the
language of the display texts are selected.
 Turn the info button until "key man-
agem." is shown on the display.
 Press Info button.
 Remove the grey Intelligent Key and in-
sert the yellow Intelligent Key to be pro-
grammed.
 Select the desired menu item to be
modified by turning the Info button.
 Press Info button.
 Adjust the menu item by turning the Info
button.
 Confirm the setting by pressing the
menu item.
 Select the next menu item to be modi-
fied by turning the Info button.
7
-
EN
 In order to save the authorisations, call
the "Save?" menu by turning the info
button and then press the info button.
 "Continue key menu":
Yes: Programme further Intelligent Key.
No: Exit key menu.
 Press Info button.
Selecting the brush shape
This function is required when changing the
cleaning head.
 Turn the info button until "brush head" is
shown on the display.
 Press Info button.
 Turn the info button until the desired
brush shape is highlighted.
 Press Info button.
 Move the hoist drive for replacement of
the cleaning head by turning the info
button:
up: Raise
down: Lower
OFF: Stop
 Exit menu: Select "OFF" by turning the
info button and press the info button.
When exiting the menu, the control per-
forms a restart.
Stopping times
 Turn the info button until "stopping
times" is shown on the display.
 Press Info button.
 Turn the info button until the desired as-
sembly is highlighted.
 Press Info button.
 Turn the info button until the desired
stopping time is reached.
 Press Info button.
Setting the battery type
 Turn the info button until "Battery menu"
is displayed.
 Press Info button.
 Turn the info button until the desired
battery type is highlighted.
 Press Info button.
Standard setting
Changes of the parameters of the individu-
al cleaning programmes that were made
during the operation are reset to the basic
setting after switching off the appliance.
 Turn the info button until "Basic setting"
is displayed.
 Press Info button.
 Turn the info button until the desired
cleaning programme is displayed.
 Press Info button.
 Turn the info button until the desired pa-
rameter is displayed.
 Press Info button - the set value blinks.
 Set the desired value by turning the info
button.
 Press Info button.
Setting the language
 Turn the info button until "Language" is
displayed.
 Press Info button.
 Turn the info button until the desired
language is highlighted.
 Press Info button.