14. Door connection box
a
Fig.
The door connection box allows for the connection of a
safety edge, a wicket door contact and slack rope switches. The
wicket door contact and the slack rope switches are electrically
connected in series and are monitored by the control. If a wicket
door is available, the wicket door contact (Entrysense 6k8 model)
is connected to the door connection box. For this purpose, re-
move the 2 kOhm resistor from the door connection box, to which
the Entrysense is clamped, and connect it there. The Entrysense
is tested in compliance with PL C as per EN 13849-1 and is mon-
itored by the door control.
As slack rope switches, switches with forced actuation complying
with the specifications of EN 60947-5-1, Annex K are to be used.
The supply line of the door connection box is to be laid at the
door leaf, well protected against damage. With pulsed operation,
connect a closing edge safety device and select the correspond-
ing setting in menu item 35. Pressing the Prog button
menu item 35 for a longer time displays the measured resistance
value of the 8k2 closing edge. Example: Value 82 means 8k2.
Pressing the Prog button
Crush hazard and risk of being struck by the
CAUTION
closing door
The pressure wave switches may only be actu-
ated after having been tested.
•
For this purpose, select the value 2 in menu
item 35.
15. Key switch / pull switch
a
Fig.
When a key switch / pull switch is connected to ter-
minal J7, the control has to be programmed accordingly. Select
the desired function in menu item 50.
16. Radio receiver
For the use of a hand-held transmitter, attach the receiver module
a
(option) to J11 (Fig.
) and connect the antenna to J12. In order
to program the hand-held transmitters, follow the instructions
provided in Programming a radio hand-held transmitter in the
Programming chapter.
17. Relay outputs
The control provides two potential-free change-over contacts
(250 V AC / 2 A or 24 V DC / 1 A).
The 24 V output at terminal X8 may be loaded with a maximum of
200 mA.
Select the desired relay function in menu items 45 and 46.
a
Fig.
Connection of an optical red-green signal encoder. Select
the value 0 in menu item 40 and the value 1 in menu item 46.
b
Fig.
Connection for the signal with automatic return.
c
Fig.
Connection for the mutual locking of 2 doors (lock circuit).
Select the value 2 or 3 in menu item 50 and value 0 in menu
item 45.
d
Fig.
Connection for the mutual locking of 3 doors (lock circuit).
Select the value 2 or 3 in menu item 50 and the value 0 in menu
items 45 and 46.
18. Light grid
As an alternative to the closing edge protection, a light grid can
be used. For this purpose, clamp the light grid as shown in
a
b
Fig.
or Fig.
. Set the value to 0 in menu item 35.
briefly will interrupt the display.
5
Programming
In order to program the Kombisteuerung, open the housing cover.
in
The programming works in a menu-controlled fashion. Carry out
all settings as specified in the Programming procedure chapter,
see also Representation of the menu structure. The Program
overview chapter shows the full scope of the menu.
If the settings are protected, an L is indicated in the display and
accessing the menu is inhibited. In order to enable the menu, you
have to give the release signal by means of the IR remote control.
Programming procedure
Proceed as follows to carry out programming settings:
1.
Press the
trol. The selection of the individual main menu (in the fol-
lowing referred to as "menu") appears on the LED display.
Up to 9 menus are provided.
2.
Navigate with buttons
The LED display shows the current selection as value 1-9.
3.
Confirm the selection with the button
in the first digit now shows the menu which you are in. The
second digit shows the current menu item in this menu.
4.
Navigate with buttons
item. A total of up to 10 menu items is provided to you
(0-9). The LED display shows the current selection in the
second digit as value 0-9.
5.
Confirm the selection with the button
value for the respective menu item blinks on the LED dis-
play.
6.
Set the desired value using the buttons
on the menu item, values between 0 and 99 can be
entered.
7.
Confirm the entry with the button
confirms the entry by 5-time blinking of the LED point and
by returning to the selection of the menu item.
8.
If you want to complete the programming, press the but-
ton
repeatedly until – – appears on the display.
9.
Confirm the selection with the button
gramming.
TAD MS 400V / 230V
button to reach the programming of the con-
to select the desired menu.
to select the desired menu
. The LED display
. The LED display
. The currently set
. Depending
to exit the pro-
EN - 25