Nemox gelato 6K crea Serie Instrucciones Para El Uso página 5

HOW TO CONNECT THE CORD TO A U.K. PLUG: IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:
•Green and yellow:
•Blue:
•Brown:
Please, read the instructions given below before connecting the cord to a plug.
If in doubt, please, consult a qualified electrician. As the colours of the wires in
the mains lead of this appliance may not correspond with the coloured
markings identifyng the terminals in your plug, proceed as follows: the wire
that is coloured Green and Yellow must be connected to the terminal in the
plug which is marked with the letter E or the Earth symbol (G), or coloured
Green or Green and Yellow.
The wire that is coloured Brown must be connected to the terminal which is
marked with the letter L or coloured Red. The wire that is coloured Blue must be
connected to the terminal which is marked with the letter N or coloured Black.
SAFETY POINTS FOR REWIRABLE OR MOULDED PLUG
The mains lead of this appliance may be already fitted with a BS1363 13A plug.
•If your socket outlet is not suitable for the plug, then the plug must be removed (cut off if it is a moulded on plug),
the flexible cord insulation should be stripped back as appropriate and a suitable 3 pin plug fitted.
•WARNING: Dispose of a plug that has been cut from the power supply cord, as such a plug is hazardous if
inserted in a live 13A socket outlet elsewhere in the house.
•Should the fuse need to be replaced an ASTA marked fuse, approved to BS 1362, of the same rating must be
used.
•Always replace the fuse cover after fitting a fuse. The plug must NOT be used if the cover is omitted or lost until a
replacement is obtained. Make certain that only the correct fuse cover is used and fitted.
•For plugs with detachable fuse cover, the replacement must be the same as the colour insert in the base of the
plug, or as directed by the embossed wording on the base of the plug.
•If the detachable fuse cover is lost a replacement may be purchased from a Service Centre.
•Information for supply may also be obtained from the plug manufacturer.
1). Cooling button.
1a). Cooling system
operation LED.
2). Mixing paddle button.
2a). Paddle operation LED.
3). Transparent lid.
3a). Hole to add ingredients
with cap.
4). Paddle locking ring.
5). Mixing paddle.
6). Ventilation grid.
7). Water discharge cap.
8). Paddle speed adjustment
knob.
9). Water discharge cap.
Congratulations!
You have purchased a latest generation
NEMOX ice cream machine.
In addition to producing all the ice cream,
sorbet and Granita you want, you can also
conserve the preparations in the pot, so they are
always at the ideal serving temperature and
density.
An onboard computer will help you get the job
done in the best way, enhancing your
professionalism and hard work and saving you
valuable time.
English
UK USERS ONLY
Earth
Neutral
Live
10). Master light switch.
11). Program selection button.
11a). Gelato italiano ice
cream program LED.
11b). Semi soft Gelato
program LED.
11c). Granita program LED.
11d). Fast cooling
program LED.
12). Preservation time
selection button.
12a). Preservation cycle
No.1 LED.
12b). Preservation cycle
No.2 LED.
12c). Preservation cycle
12d). Preservation cycle
13). Oil seal.
14). Spatula.
15). Paddle plastic sleeve gasket set.
16). Water discharge tap gasket set.
17). Paddle plastic sleeve.
18). Vertical scraper.
19). Horizontal scraper.
20). Interlocking buffer.
21). Cleaner.
Your ice cream machine has two types of
operation:
• M a n u a l m o d e , t h e o p e r a t i o n o f t h e
compressor and paddle are independent so
as to make the most of your experience. The
preservation system can be started on its own
if you consider it appropriate. An electronic
device stops the paddle when the consistency
of the preparation is excessive, thus
preventing compromising the mechanical
functions of the machine. The cooling system
will continue to run until it is manually stopped.
No.3 LED.
No.4 LED.
5