Operation; Function /Select; Master Volume Control; Surround Mode Button - Denon ADV-700 Instrucciones De Operación

12

OPERATION

3
c 8 1:02:46
1
DVD
TONE
1,3 5
Playing the input source
1 Either turn the FUNCTION/SELECT dial on the main unit
or press the FUNCTION button on the remote control
unit to select the input source you want to play.
FUNCTION
FUNCTION
/SELECT
Main unit Remote control unit
• The function switches as shown below.
• The function only changes in the "Æ" direction when
operated from the remote control unit.
TUNER DVD TV/DBS
CDR/TAPE VCR V.AUX
2 If "DVD", "TV/DBS" or "V.AUX" is selected as the
input source, press the INPUT MODE button on the
remote control unit to select the input mode.
INPUT MODE
Remote control unit
AUTO PCM DTS ANALOG
• "ANALOG" cannot be selected when "DVD" is
selected as the input source.
Input mode selection function
This can be selected for the "DVD", "TV/DBS" and
"V.AUX" input sources.
Different input modes can be selected for the
different input sources. The selected input modes
for the separate input sources are stored in the
memory.
q AUTO (auto mode)
In this mode, the types of signals being input to the
digital and analog input jacks for the selected input
source are detected and the program in the ADV-
700's surround decoder is selected automatically
upon playback.
All manuals and user guides at all-guides.com
POWER
CH
OFF 4 5 6
VCR POWER VCR POWER
CH VOL
CLEAR 7 8 9
TV
TV POWER TV POWER CH SLEEP
TV/VCR
0
CALL +10
DISPLAY RETURN INPUT MODE SURROUND
3
2
MENU FUNCTION
1
ENTER
5
MODE
VOLUME
BAND
MUTE
CH SHIFT
The presence or absence of digital signals is
detected, the signals input to the digital input are
identified and decoding and playback are performed
automatically in DTS, Dolby Digital or PCM (2
channel stereo) format. If no digital signal (TV/DBS
and V.AUX) is being input, the analog input jacks are
selected.
Use this mode to play Dolby Digital signals.
w PCM (exclusive PCM signal playback mode)
Decoding and playback are only performed when
PCM signals are being input.
Note that noise may be generated when using this
mode to play signals other than PCM signals.
e DTS (exclusive DTS signal playback mode)
Decoding and playback are only performed when
DTS signals are being input.
r ANALOG (exclusive analog audio signal playback
mode)
The signals input to the analog input jacks are
decoded and played.
(This cannot be selected in the DVD mode.)
NOTE:
• The input mode is automatically set to "AUTO" when
the input is switched to DVD.
3 Either press the SURROUND MODE button on the
main unit then turn the FUNCTION/SELECT dial or
press the SURROUND button on the remote control
unit to select the play mode.
SURROUND
FUNCTION
SURROUND
MODE
/SELECT
\
Remote control
Main unit Main unit
unit
• The function switches as shown below.
• The function only changes in the "Æ" direction when
operated from the remote control unit.
STEREO AUTO DECODE 5CH STEREO MONO MOVIE
ROCK ARENA JAZZ CLUB VIDEO GAME
MATRIX VIRTUAL DIRECT STEREO
4 Start playback on the selected component.
• For operating instructions, refer to the component's
manual.
5 Either turn the MASTER VOLUME dial on the main unit
or use the VOLUME buttons on the remote control unit
to adjust the volume.
The volume level is displayed on
M.VOLUME -20
the display.
MASTER VOLUME
Main unit Remote control unit
• The volume can be adjusted within the range of –60
to 0 to 18 dB. However, when the channel level is set
as described, if the volume for any channel is set at
+1 dB or greater, the volume cannot be adjusted up
to 18 dB. (In this case the maximum volume
adjustment range is "18 dB — (Maximum value of
channel level)".)
NOTE:
• The digital input indicator will light when "DIG" playing
CD-ROMs containing data other than audio signals, but
no sound will be heard.
Input mode when playing DTS sources
• Noise will be output if DTS-compatible CDs or LDs are
played in the "ANALOG" or "PCM" mode.
When playing DTS-compatible sources, be sure to
connect the source component to the digital input jacks
(OPTICAL/COAXIAL) and set the input mode to "DTS".
• Noise may be generated at the beginning of playback
and while searching during DTS playback in the AUTO
mode. If so, play in the DTS mode.
2 Checking the currently playing program source, etc.
Either press the STATUS button on the main unit then
turn the FUNCTION / SELECT dial or press the STATUS
button on the remote control unit to check the unit's
operating status.
FUNCTION
/SELECT
\
STATUS
Main unit Main unit
...
Input mode display
DIG AUTO
• In the AUTO mode
ANA
• In the DIGITAL
DIG AUTO
ANA
PCM mode
• In the DIGITAL
DIG AUTO
ANA
DTS mode
DIG AUTO
• In the ANALOG
ANA
mode
VOLUME
Input signal display
• DOLBY DIGITAL
DIG PCM
DIGITAL
• DTS
DIG PCM
DIGITAL
• PCM DIG PCM
DIGITAL
• The "DIG" lights when digital signals are being input
properly. If the LED does not light, check whether the digital
input component setup and connections are correct and
whether the component's power is turned on.
STATUS
Remote control
unit
ENGLISH
Lit
PCM DTS
One of these lights, depending
on the input signal.
PCM DTS
PCM DTS
PCM DTS
DTS
PRO LOGIC II
One of these
lights,
DTS
depending on
the input signal.
DTS
19