English - Scott A6 2019 Manual Del Usuario

• BASIC STRAP DIVIDERS: IF YOU DO NOT HAVE LOW
PROFILE OR CAM STRAP DIVIDER WHICH OPEN YOU
CAN CARRY OUT THE FOLLOWING STEPS BY FEEDING
THE STRAPS THROUGH THE STANDARD DIVIDERS.
• ALL STRAPS: THE DIVIDERS SHOULD BE POSITIONED
BELOW AND SLIGHTLY IN FRONT OF THE EARS. THE
STRAPS SHOULD NOT COVER YOUR EARS.
STRAP LENGTHS SHOULD ALWAYS BE EVEN STRAP DIVIDERS
SIT BELOW AND SLIGHTLY IN FRONT OF THE EARS.
IN THE EVENT THE STRAPS ARE UNEVEN LENGTHS BETWEEN
THE TWO SIDES PLEASE NOTE THAT THE STRAPS CAN BE
EVENED OUT BY PULLING THEM TO EITHER SIDE THROUGH
THE MOUNT ON THE BACK OF THE HELMET.
CHIN STRAP ADJUSTMENT:
WHILE WEARING THE HELMET, THE CHIN STRAPS MUST ALWAYS BE SECURED BY THE CLIP AND PULLED TIGHT. (N) &
(O) SHOW HOW THE CLIP IS OPENED AND CLOSED. (P) SHOWS THE CORRECT POSITION AND FIT OF THE CHIN STRAP
DURING USE. AFTER CORRECTLY SIZING THE CHIN STRAP ENSURE THAT THE LOOSE END OF THE CHIN STRAP HAS
BEEN GUIDED THROUGH AND SECURED BY THE RUBBER O-RING (Q). IF THIS IS NOT DONE THE CHIN STRAP MAY
BECOME LOOSE, COMPROMISING THE FIT AND SAFETY OF THE HELMET.
MAKE SURE THAT THE CHIN STRAP IS WORN CLOSE TO THE TOP OF THE NECK (P). IF THE STRAP IS WORN ON THE
TIP OF THE CHIN, THEN THE PROBABILITY OF THE HELMET COMING OFF IN AN ACCIDENT IS INCREASED.
N O

ENGLISH - 6

SYSTEM 1 SYSTEM 2
P Q
• ALL CHINSTRAP : ALL LIABILITY CLAIMS BASED UPON NON-OBSERVANCE OF THE INSTRUCTIONS FOR FITMENT
AND USE EXPLAINED IN POINT 3 ARE PRECLUDED.
• IV. FIT SYSTEM ADJUSTMENT
SCOTT INCLUDES A HELMET FIT SYSTEM ON CERTAIN MODELS TO ENSURE THE HELMET FITS PROPERLY AND IS HELD
SECURELY AND COMFORTABLY ON YOUR HEAD SCOTT OFFERS DIFFERENT FIT SYSTEMS ON DIFFERENT HELMETS.
IF YOUR HELMET IS EQUIPPED WITH A FIT SYSTEM, BELOW YOU WILL FIND INSTRUCTIONS ON HOW TO ADJUST IT
CORRECTLY TO ACHIVE A PERFECT FIT.
• ALL FIT SYSTEMS : TURN THE DIAL ON THE BACK OF THE FIT SYSTEM CLOCKWISE TO ATTAIN A SMALLER SNUGGER
HELMET FIT (R) AND COUNTERCLOCKWISE TO INCREASE THE SIZE OF THE FIT (S). AFTER ADJUSTING THE FIT
SYSTEM THE HELMET SHOULD FIT YOUR HEAD SECURELY AND COMFORTABLY.
R
HEIGHT ADJUSTMENT OF THE SOLO AND MRAS FIT SYSTEMS
FIND YOUR HELMET AND FIT SYSTEM AT WWW.SCOTT-SPORTS.COM OR HELMET BOX.
HEIGHT ADJUSTMENT OF THE REAR OF THE FIT SYSTEM IS A GREAT WAY TO ACHIEVE A PERFECT FIT. THE FACTORY
POSITION IS GOOD FOR THE MAJORITY OF USERS, HOWEVER SOME RIDERS MAY FIND ONE OF THE OTHER TWO
POSITIONS WORKS BETTER FOR THEM. ADJUSTING THE HEIGHT AT THE REAR CAN ALSO ADJUST THE HEIGHT OF THE
FRONT OF THE HELMET ON THE HEAD.
• MRAS OR SOLO FIT SYSTEM : IF YOUR HELMET IS FITTED WITH
AN MRAS OR SOLO FIT SYSTEM, YOU CAN ADJUST THE HEIGHT
BY CHANGING THE POSITION OF THE CONNECTION WITH THE
HELMET. TO DO THIS, SIMPLY UNCLICK (FIRM PULLING MOTION)
THE ARMS OF THE FIT SYSTEM FROM THE SIDES OF THE HEL-
MET AND REINSERT THEM INTO THE UPPER OR LOWER HOLE.
• HALO FIT SYSTEM : IF YOUR HELMET IS FITTED WITH A HALO FIT SYS-
TEM, YOU CAN EASILY ADJUST THE HEIGHT WHEN THE HELMET IS ON
YOUR HEAD. IF YOUR HELMET DOES NOT FIT YOUR HEAD COMFORT-
ABLY WHEN IN THE MIDDLE POSITION, THEN PUSH THE REAR OF THE
FIT SYSTEM UP OR PULL IT DOWN TO ADJUST THE HEIGHT OF THE
REAR OF THE FIT SYSTEM. THERE ARE 3 POSITIONS IN TOTAL.
PLEASE MAKE SURE THAT EACH ARM OF THE FIT SYSTEM IS SECURE-
LY CLICKED INTO THE HELMET.
S
1
2
3
7 - ENGLISH