Tabla de contenido
Instalação da unidade interna (cont.)
Tubulações do fluido refrigerante
O sentido da tubulação pode ser feita nas 3 direções indicadas na figura.
Se as conexões forem feitas em uma das laterais, destaque o alívio
existente para passagem da tubulação.
Direcione as tubulações até a passagem na parede e envolva-as
juntamente com os cabos de interconexão e a mangueira de drenagem.
A mangueira de drenagem deve estar localizada na parte inferior para
facilitar o escoamento da água.
•
Não remova as tampas das extremidades das tubulações até que
estejam conectadas, para evitar a entrada de umidade e poeira.
•
Para estender as tubulações, desenrole-as, conforme mostrado
na figura.
Conexão da tubulação a unidade interna
•
Remova as tampas das extremidades. Verifique se estão livres de
sujeira e rebarbas.
•
Insira a porca curta no tubo de cobre e faça o flangeamento na
extremidade.
•
Ajuste as conexões usando duas chaves, girando-as em
direções opostas.
Dreno de água condensada da unidade interna
A instalação correta da drenagem de condensado é um ponto
fundamental na instalação do equipamento.
1.
Coloque a mangueira de drenagem na parte inferior do conjunto de
interconexão, tomando cuidado para não formar sifões.
2.
A mangueira de drenagem deve manter ao longo de sua extensão no
sentido descendente para facilitar o escoamento de água.
3.
Não dobre a ponta da mangueira de drenagem nem a coloque abaixo
do nível da água.
4.
Se a saída das tubulações for feita pela direita do equipamento,
estas devem ser presas na parte de trás do equipamento.
5.
Insira a conexão da mangueira no furo de passagem da parede.
6.
Pressione para unir a conexão de dreno a mangueira de dreno.
17
810415LO_MAN_TRANE_FIXO.indd 17
INSTALLATION MANUAL---Installation of the Indoor unit
Refrigerant piping connection
INSTALLATION MANUAL---Installation of the Indoor unit
The piping can be run in the 3 directions indicated by
numbers in the picture . When the piping is run in
Refrigerant piping connection
INSTALLATION MANUAL---Installation of the Indoor unit
direction 1or3, cut a notch along the groove on the side
of the indoor unit with a cutter.
The piping can be run in the 3 directions indicated by
Run the piping in the direction of the wall hole and bind
numbers in the picture . When the piping is run in
Refrigerant piping connection
the copper pipes , the drain pipe and the power cables
direction 1or3, cut a notch along the groove on the side
together with the tape with the drain pipe at the bottom,
of the indoor unit with a cutter.
The piping can be run in the 3 directions indicated by
so that water can flow freely.
Run the piping in the direction of the wall hole and bind
numbers in the picture . When the piping is run in
the copper pipes , the drain pipe and the power cables
Do not remove the cap from the pipe until connecting
direction 1or3, cut a notch along the groove on the side
together with the tape with the drain pipe at the bottom,
it, to avoid dampness or dirt from entering.
of the indoor unit with a cutter.
so that water can flow freely.
If the pipe is bent or pulled too often , it will become
Run the piping in the direction of the wall hole and bind
stiff . Do not bend the pipe more than three times at
the copper pipes , the drain pipe and the power cables
Do not remove the cap from the pipe until connecting
one point.
together with the tape with the drain pipe at the bottom,
it, to avoid dampness or dirt from entering.
When extending the rolled pipe, straighten the pipe by
so that water can flow freely.
If the pipe is bent or pulled too often , it will become
unwinding it gently as shown in the picture.
stiff . Do not bend the pipe more than three times at
Do not remove the cap from the pipe until connecting
one point.
it, to avoid dampness or dirt from entering.
When extending the rolled pipe, straighten the pipe by
If the pipe is bent or pulled too often , it will become
unwinding it gently as shown in the picture.
stiff . Do not bend the pipe more than three times at
Connections to the indoor unit
one point.
When extending the rolled pipe, straighten the pipe by
unwinding it gently as shown in the picture.
1. Remove the indoor unit pipe cap (check that there is
Connections to the indoor unit
no debris inside).
2. Insert the fare nut and create a flange at the extreme
end of the connection pipe.
1. Remove the indoor unit pipe cap (check that there is
3. Tighten the connections by using two wrenches
Connections to the indoor unit
no debris inside).
working in opposite directions
2. Insert the fare nut and create a flange at the extreme
end of the connection pipe.
1. Remove the indoor unit pipe cap (check that there is
3. Tighten the connections by using two wrenches
Indoor unit condensed water drainage
no debris inside).
working in opposite directions
2. Insert the fare nut and create a flange at the extreme
end of the connection pipe.
The indoor unit condensed water drainage is fundamen-
3. Tighten the connections by using two wrenches
tal for the success of the installation.
Indoor unit condensed water drainage
working in opposite directions
1. Place the drain hose below the piping, taking care not
The indoor unit condensed water drainage is fundamen-
to create siphons.
tal for the success of the installation.
Indoor unit condensed water drainage
2. The drain hose must slant downwards to aid drainage.
3. Do not bend the drain hose or leave it protruding or
1. Place the drain hose below the piping, taking care not
twisted and do not put the end of it in water . If an
The indoor unit condensed water drainage is fundamen-
to create siphons.
extension is connected to the drain hose , ensure that
tal for the success of the installation.
2. The drain hose must slant downwards to aid drainage.
it is lagged when it passes into the indoor unit.
3. Do not bend the drain hose or leave it protruding or
1. Place the drain hose below the piping, taking care not
4. If the piping is installed to the right, the pipes, power
twisted and do not put the end of it in water . If an
to create siphons.
cable and drain hose must be lagged and secured onto
extension is connected to the drain hose , ensure that
2. The drain hose must slant downwards to aid drainage.
the rear of the unit with a pipe connection.
it is lagged when it passes into the indoor unit.
3. Do not bend the drain hose or leave it protruding or
1) Insert the pipe connection into the relative slot.
4. If the piping is installed to the right, the pipes, power
twisted and do not put the end of it in water . If an
2) Press to join the pipe connection to the base.
cable and drain hose must be lagged and secured onto
extension is connected to the drain hose , ensure that
the rear of the unit with a pipe connection.
it is lagged when it passes into the indoor unit.
1) Insert the pipe connection into the relative slot.
4. If the piping is installed to the right, the pipes, power
2) Press to join the pipe connection to the base.
cable and drain hose must be lagged and secured onto
the rear of the unit with a pipe connection.
1) Insert the pipe connection into the relative slot.
2) Press to join the pipe connection to the base.
Instalação da unidade
1
1
2
3
1
2
3
2
3
Curve os tubos até a saída
Shape the connection pipe
Shape the connection pipe
YES
NO
SIM
NÃO
Extending the rolled pipe
Shape the connection pipe
Como desenrolar os tubos
YES
NO
Extending the rolled pipe
YES
NO
Extending the rolled pipe
YES
YES
YES
SIM
NO
NO
18
NO
NÃO
18
18
torque wrench
torque wrench
Torquímetro
torque wrench
NO
NO
NO
NÃO
2019-09-16 2:00:34 PM
Tabla de contenido
