Important Remarks; Electronic Programmer - Cardin Elettronica PRG813 Manual Del Usuario

IMPORTANT REMARKS

TO REDUCE THE RISK OF SEVERE INJURY OR DEATH READ THE FOLLOWING REMARKS CARE-
FULLY BEFORE PROCEEDING WITH THE INSTALLATION. PAY PARTICULAR ATTENTION TO
ALL THE PARAGRAPHS MARKED WITH THE SYMBOL
INSTRUCTIONS COULD COMPROMISE THE CORRECT WORKING ORDER OF THE SYSTEM.
• These instructions are aimed at professionally qualified "installers of
electrical equipment" and must respect the local standards and regula-
tions in force.
• All materials used must be approved and must suit the environment in
which the installation is situated.
• This product and all its relative components has been designed and
manufactured by Cardin Elettronica who have verified that the product
conforms in every aspect to the safety standards in force.
The resulting installation and any non authorised modifications are the
complete responsibility of the installer and all maintenance operations
must be carried out by professionally qualified technicians.
• This electronic programmer is not fitted with a torque limiter and must
only be used exclusively for the purpose for which it has been made.
"i.e. for the command and control of double gate installations with
230 Vac motors"
• The manufacturer accepts no liability for situations arising from the use
of an electrical installation which does not conform to the local standards
and regulations in force
PROGRAMMER INSTALLATION
General description
• All weather container in ABS with a door
sealing gasket.
• Container fitted with wall fastening ele-
ments.
• Power cable inlet for the insertion of Ø16
mm tubes.
• Protection grade IP55.
• Fireproofing grade UL94V2.
Positioning
Depending on the type of installation, work out the position in which the
programmer will be situated remembering that the site must be:
- a position safe from accidental collision;
- high enough above the ground to be safe from pools of water;
- in a position which the technician can easily reach.
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
Drawing number :
Container installation
Product Code :
Attention! Fixing the container to the wall does not require you to dismantle
Draft :
the circuit-board.
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Opening the container
Unfasten the four spring loaded screws, using a flat nosed screwdriver (
det. 1), by rotating them 90° with respect to the locked position. At this
point remove the cover as indicated in the drawing
Note: To close the container replace the lid making sure that the sealing
gasket is perfectly positioned and then press in the spring loaded screws
and turn them back through 90° to the initial position.
IMPORTANT REMARKS
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
Scattola (dimensioni d'ingombro)
Description :
DM0263
PRG 807
PRG-807
Date : 22-04-97
P.J.Heath
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
. NOT READING THESE IMPORTANT
Fastening the container to the wall
Using the container as a template mark the four points at which the fas-
tening holes are to be drilled;
- Fasten the container using four M4 type screws and raw plugs "B" and
insert the screw covering plugs "C".
Inserting the rigid electrical connection pipes
Check that the pipe holders are securely
fastened:
- insert the rigid electrical connection pipes
"1-2-3 and 4" into the pipe holders;
- the 230 Vac cables should be passed
through pipes 3 and 4 (see figure) so as to
separate them from the low voltage wires
which should be passed through pipes 1
and 2;
Drawing number : DM0264
- carry out the electrical connection following
Product Code : PRG-807
the wiring diagram on page 7.
Date :
Draft : P.J.Heath 22-04-97
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831

ELECTRONIC PROGRAMMER

Electronic control unit for two 230 Vac motors with an incorporated radio
receiver card, which allows the memorisation of 300 user codes.
The "rolling code" type decoder uses 433.92 MHz (S449) series trans-
mitters.
Programming is carried out using one button and allows you to set the
opening and closing work times.
• After having installed the device, and before powering up the
programmer, release the door (manual release mechanism) and
move it manually, checking that it moves smoothly and has no
unusual points of resistance.
• The programmer is not fitted with a torque limiter; therefore
the safety of the appliance must be guaranteed by installing
1 the relevant safety devices.
• Connect the operator with the greatest travel time to the
"motor 2" output (binding posts 17-18-19).
2
• Before connecting the appliance make sure that the voltage and
frequency rated on the data plate conform to those of the mains
supply.
• An all pole trip switch with at least 3 mm between the contacts
must be installed between the unit and the mains supply.
• Don't use cables with aluminium conductors; don't solder the
ends of cables which are to be inserted into the binding posts; use
cables marked T min 85°C and resistant to atmospheric agents.
• The terminal wires must be positioned in such a way that both the
wire and the insulating sheath are tightly fastened (a plastic jubilee
clip is sufficient).
6
IMPORTANT REMARKS
All rights reserved. Unauthorised copying or use of the information contained
B
Scattola (installazione scattola)
Description :
PRG 807
1
Description :
Drawing number : DM0287
Product Code : PRG-811
Draft : P.J.Heath Date : 11-06-97
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0
4
3
2
Scattola Liberali (insta
PRG 811