Tabla de contenido
Idiomas disponibles
Idiomas disponibles
IMPORTANT REMARKS
TO REdUCE THE RISK OF SEVERE INJURY OR dEATH REAd THE FOLLOWING REMARKS
CAREFULLY BEFORE PROCEEdING WITH THE INSTALLATION. PAY PARTICULAR ATTENTION
TO ALL THE PARAGRAPHS MARKEd WITH THE SYMBOL
INSTRUCTIONS COULd COMPROMISE THE CORRECT WORKING ORdER OF THE SYSTEM.
• These instructions are aimed at professionally qualified "INSTALLERS
OF ELECTRICAL EqUIPMENT" and must respect the local standards
and regulations in force. All materials used must be approved and
must suit the environment in which the installation is situated.
• All maintenance operations must be carried out by professionally
qualified technicians. Before carrying out any cleaning or main-
tenance operations make sure the power is disconnected at the
mains.
• This appliance must be used exclusively for the purpose for which
it has been made. "i.e. for the automation counterbalanced
garage doors" Any non authorised modifications are to be consid-
ered improper and therefore dangerous. The manufacturer accepts
no liability for situations arising from an installation which does not
conform to the local standards and regulations in force.
IMPORTANT! The geared motor 30/GL2024 is not fitted with
a torque limiter. Only use an electronic programmer which has
a torque limiter with maximum force at the head of the gate
equal to 50N (local standards and regulations in force).
USE
The appliance 30/GL2024 may be used to operate single or articulated
garage door of up to 2m
with a maximum weight of 80Kg (central
2
motor) For garage doors with a width of over 4m and not more than
2,7m in height (max. weight 80Kg) and for garage doors with a pedes-
trian access door two motors are required (one motor with electronics
and one without).
IMPORTANT SAFETY INSTRUCTIONS
It is the responsibility of the installer to make sure that the following
public safety conditions are satisfied:
1) The pedestrian door must not open on its own, e.g.; swing open
while the garage door is in movement
2) The appliance must not be operated when the pedestrian door is
not fully closed.
3) Make sure that there are no dangerous sharp edges (R=3mm
min.)
4) Make sure that the end-user is aware that children and/or pets must
not be allowed to play within the area of a garage door installation.
If possible include this in the warning signs.
5) A correct earth connection is fundamental in order to guarantee the
electrical safety of the machine
6) If you have any questions about the safety of the gate operating
system, do not install the operator. Contact your dealer for assist-
ance.
TECHNICAL dESCRIPTION
• Single piece geared reduction unit.
• 24V direct current drive motor with a permanently lubricated revers-
ible reduction unit mounted on a cast iron stator.
• Manual release mechanism
• Base in zinc-plated steel
• Carter in shock-proof plastic
• Night light
ACCESSORIES
36/GLO2Ad -
Straight telescopic arm length 700.
36/GLO3A
-
Curved (right) telescopic arm length 700.
36/GLO4A
-
Curved (left) telescopic arm length 700.
36/GLO6A
-
Straight telescopic arm length 1000.
36/GLOPS
-
Motor support extension.
36/GLOTG -
Pair of pipes, pipe support brackets and DIN
threaded pins for central motor positioning.
36/GLOCGL -
Ferrule and DIN threaded pin, with pipe support
brackets for lateral motor positioning.
36/GL20SB -
Manual release cord.
IMPORTANT REMARKS
USER INSTRUCTIONS
During the opening/closing manoeuvre check for correct operation
and activate the emergency stop button in case of danger.
The appliance must not be activated in the dark therefore make
sure that the night lights function correctly. The appliance can be
manually released in case of emergency (see manual release on
page 15). Periodically check the moving parts for wear and tear
and grease if required, using lubricants which maintain their friction
levels unaltered throughout time and are suitable for temperatures
of -20 to +70°C.
In case of failure or operational anomalies switch off the power at
the mains do not attempt to repair the appliance yourself.
Periodically check the correct operation of all safety devices (pho-
toelectric cells etc.).
INSTALLATION INSTRUCTIONS
Eventual repair work must be carried out by specialised personnel
using original spare parts. The appliance is not suitable for continu-
ous operation and must be contained within the value stipulated
(see technical data on page 28).
The minimum controls which may be installed are OPEN-STOP-
CLOSE, these controls must be installed in a location not acces-
sible to children.
Before starting with the installation of the system check that the
structure which is to be automated is in good working order and
respects the local standards and regulations in force. Automating
an existing system which has sliding or balancing problems will not
solve those problems and may even make them worse by placing
more stress on weakened or damaged areas. To this end make
sure that the runner guides slide freely and grease all the moving
parts (pins, castors etc.) using lubricants which maintain unaltered
friction characteristics over a period of time and are suitable for
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
temperatures of -20 to +70°C.
FITTING THE UNIT
Fitting the motor centrally
1) Remove the motor from its positioning base "A" fasten the two
motor base extensions "B" to the positioning base. Mark the
position of the motor axis on the positioning base "A" and fasten
the complete profile "A" and "B" to the cross piece of the garage
door. The motor axis must be 70mm below the hinged point of
the door arm "C". (for non flush fitting garage doors) or half way
up for flush fitting garage doors (see figs 2-3).
The motor support, complete with its extensions, must be fitted
to the side of the lock and has to cover at least three cross pieces
"d", "E" and "F" using a minimum of three Ø 5mm rivets for each
cross piece.
230mm
3
IMPORTANT REMARKS
. NOT REAdING THESE IMPORTANT
d
B
E
A
70mm
N
B
F
9
G
H
C
M
L
Tabla de contenido
