Scheppach Tisa 3.0 Traducción De La Instrucción De Original página 19

wing nut has been loosened.
Check the 90° and the 45° position before the first and
each subsequent startup.
Make a test cut! Readjust the angle adjustment on the ad-
justing bolts 1 & 2.
Saw Blade Height Adjustment, Fig. M
The saw blade is adjustable from 0 to 80 mm cutting
height after the wing nut has been loosened. For safe and
clean working, choose a minimal saw blade projection for
the workpiece.
Length Cuts, Fig. N
Insert the length stop for parallel cuts.
Use the stop ruler with the high stop side for cuts above
120 mm and the stop ruler with the low stop side for cut
widths under 120 mm.
Lead the workpiece with the push stick.
1 high hub
2 Iow hub
Diagonal Cuts
For diagonal and angle cuts, insert the cross-cutting guide
or the slide carriages. Both parts are available as special
accessories. The setting scale of the cross-cutting guide
reaches from 0° - 90°.
Notes on working
Working on circular saw benches
Edging and slitting, Fig. A
Tool: length cut circular saw blade
Work step:
Before beginning to edge a work piece, return and lock the
edging carriage. First press the work piece into the point
of the carriage arm, and then fasten to the opposite point
by shifting the guide arm. The edging may begin after
pulling the unlatching cord. Pieces which are not perfectly
flat should be placed with the concave side downwards.
A firm hold can be achieved by shifting the forward steel
point.
Keep hand flat on the work piece and outside the plane
of the saw. The fingers should be closed and the thumbs
closely fitting.
Cutting thicker work pieces, Fig. B
(Width of the processed work piece greater than 120 mm)
Tool: circular saw blade for length cuts
Work step:
Adjustthe parallel stop to the width of the intended work
piece. Pay attention to safe hand rests. If small wood
pieces separat while cutting, then feed only with the right
hand or with the assistance of a push board. If a danger
exists that the work piece will jam between the circular
saw blade, the splitting wedge and the stop, then the stop
is to be returned as far as the middle of the saw blade or a
shorter auxiliary stop should be used.
In the drawings on pages K4/K5, the upper machine cover
has only been outlined, or in one case completely left out,
in order to more clearly show work steps or attachments.
14 english
Remember, the machine cover is required in all the work
steps indicated on pages K4/K5.
Cutting narrow work pieces, Fig. C
(Width of work piece less than 120 mm)
Tool: circular saw blade for length cuts
Work step:
Adjust the parallel stops to the width of the intended work
piece. Feed work piece with both hands. In the area of the
saw blade use the push stick and push the work piece be-
yond the splitting wedge. When working with shorter work
pieces use the push stick from the very beginning.
Cutting strips and corners, Fig. D
Tool: Circular saw blade for line cuts
Work step:
Install parallel stops with a flatter guide side or use lower
auxiliary stops. Feed the work piece with a push board un-
til the end of the work piece is in the area of the splitting
wedge. Prevent longer work pieces from tipping over at the
end of the cutting process by using the bench extension.
Note: Attachments which require a connection to parts of
the machine must be bolted down. Screw clamps can only
provide secondary connections to machines.
Cross-cutting narrow work pieces, Fig. E
Tool: Fine toothed cross cut blade
Work step:
Adjust diversion strip so that sawed off pieces cannot
come into contact with the protruding part of the saw
blade. Feed the work piece only with the cross stop or with
the cross slide. Do not use hands to remove excess wood
from the area of the work piece.
Blind cutting, mortise and tenon, Fig. F + G
Work step:
Adjust the splitting wedge to be the rear machine cover
(Setting for blind cut). Adjust the parallel stop to the
mortise or tenon dimension and secure against sideward
movements.
Feed work piece with feeding batten. Right hand secures
the work piece against falling over. Do not place hand on
the forward edge of the work piece.
After cutting, return the feeding batten with the work
piece. The measurements of the work piece receiver re-
bate of the feeding batten must correspond to the work
piece measurements. In order to apply sufficient pressure
to the work piece, the notching depth must be approx 1
mm less than the thickness of the work piece. If the mor-
tise depth or the tenon height attains the measure of the
stop height C, than a detachable board B secured with
screws A can be used for raising the stop.
Blind cutting, rebates, Fig. H
Tool: circular saw blade for line cuts
Work step:
When rebating on the stop, select the order of cuts so that
the cut strip comes out on the side of the saw blade not
lacing the stop.
In order to perform blind cuts and rebates, remove the up-