Gardol GMSH 40+ Manual De Instrucciones página 9

ENGINE PRE-START CHECKS ENGINE PRE-START CHECKS
WARNING:
WARNING:
Never start or operate Never start or operate
the saw unless the bar and chain are
the saw unless the bar and chain are
properlyinstalled.
properlyinstalled.
1. Fill the fuel tank (A) with correct fuel 1. Fill the fuel tank (A) with correct fuel
mixture. (Fig. 7). mixture. (Fig. 8).
2. Fill the oil tank (B) with correct chain and
2. Fill the oil tank (B) with correct chain and
bar oil (Fig. 7). bar oil (Fig. 8).
3. Be certain the chain brake is engaged 3. Be certain the chain brake is disengaged
(C) before starting unit (Fig. 7).
(C) before starting unit (Fig. 8).
C
Fig. 7 Fig. 8
TO START ENGINE TO START ENGINE
1. Move ON/OFF switch
1. Move ON/OFF switch
position. (Fig. 8A)
position. (Fig. 9A)
2. Pull choke lever/throttle (A) advance. This 2. Pull choke lever/throttle (A) advance. This
sets choke and advances throttle for sets choke and advances throttle for
easier starting. (Fig. 8B)
easier starting. (Fig. 9B)
3. Press primer bulb (B) 10 times. (Fig. 8C) 3. Press primer bulb (B) 10 times. (Fig. 9C)
4. With saw on ground, grip front handle 4. With saw on ground, grip front handle
firmly with left hand and place right foot
firmly with left hand and place right foot
inside rear handle. Pull starter rope 4
inside rear handle. Pull starter rope 4
times with right hand. (Fig. 8D) times with right hand. (Fig. 9D)
NOTE: Easy Start significant reduce the
NOTE: If the engine sounds as if it wants
effort required to start the engine. You must
to start before the 4th pull, end the tugging
pull the starter rope out far enough to hear of the starter and proceed as described in
the engine attempt to start. There is no need the next step.
to pull the rope briskly-- there is no harsh
5. Push choke lever
resistance when pulling. Be aware that this
completely. (Fig. 9E)
starting method is vastly different from (and
6. Pull starter rope quickly until engine
much easier than) what you may be used to.
starts.
5. Push choke lever
7. Allow the engine to run for about 10
completely. (Fig. 8E) seconds. Squeeze and release throttle
6. Pull starter rope quickly until engine trigger (D) to idle engine. (Fig. 9F)
starts.
8. If the eingine does not start up, repeat
7. Squeeze and release throttle trigger (D) the above steps.
to idle engine. (Fig. 8F) Allow the engine
to run for about 10 seconds.
A
8. If the engine does not start up, repeat
the above steps.
A
B
Fig. 8A
B
C
Fig. 8C
OPERATION
OPERATION
RE-STARTING A WARM ENGINE
1. Make sure the on/off switch is in the "I"
C
position.
2. Depress the primer bulb 10 times.
3. Pull
times. The engine should start.
Fig. 8E
4. If the engine still can not start, follow the
step as "To start engine" in this user
RE-STARTING A WARM ENGINE
manual.
1. Make
TO STOP ENGINE
on/off switch is in
1. Release trigger and allow engine
the "I" position.
return to idle speed.
2. Depress the primer
A
2. Press STOP switch down to stop engine
bulb 10 times.
Figure 9G.
3. Pull
NOTE: For emergency stopping, simply
rope
activate CHAIN BRAKE and
times. The engine
B
STOP switch down.
should start.
4. If the engine still can not start, follow the
step as "To start engine" in this user
manual.
TO STOP ENGINE
to ON "I"
to ON "I"
1. Release trigger and allow engine
return to idle speed.
2. Press STOP switch down to stop engine.
(Figure 9)
CHAIN BRAKE OPERATIONAL TEST
NOTE: For emergency stopping, simply
Test the CHAIN BRAKE periodically to
activate CHAIN BRAKE and
ensure proper function.
STOP switch down.
Perform a CHAIN BRAKE test prior to initial
CHAIN BRAKE OPERATIONAL TEST
cutting, following extensive cutting, and
definitely following any CHAIN BRAKE
Test the CHAIN BRAKE periodically to
service.
ensure proper function.
TEST CHAIN BRAKE AS FOLLOWS:
Perform a CHAIN BRAKE test prior to initial
cutting, following extensive cutting, and
1. Place saw on a clear, firm, flat surface.
(C) in definitely following any CHAIN BRAKE
2. Start engine.
service.
3. Grasp the rear handle (A) with your right
TEST CHAIN BRAKE AS FOLLOWS:
hand (Fig. 10).
4. With your left hand, hold the front
1. Place saw on a clear, firm, flat surface.
(C) in
handle (B) [not CHAIN BRAKElever (C)]
2. Start engine.
firmly (Fig. 10).
3. Grasp the rear handle (A) with your right
5. Squeeze the throttle trigger to 1/3 throttle,
hand (Fig. 10).
then immediately activate the CHAIN
4. With your left hand, hold the front
BRAKE lever (C) (Fig. 10).
handle (B) [not CHAIN BRAKElever (C)]
6. Chain should stop abruptly. When it does,
firmly (Fig. 10).
immediately release the throttle trigger.
5. Squeeze the throttle trigger to 1/3 throttle,
then immediately activate the CHAIN
WARNING:
BRAKE lever (C) (Fig. 10).
slowly and deliberately. Keep the chain
6. Chain should stop abruptly. When it does,
from touching anything; don t let the saw tip
immediately release the throttle trigger.
forward.
WARNING:
7. If chain brake functions properly, turn the
slowly and deliberately. Keep the chain
engine off and return the chain brake to
from touching anything; don t let the saw tip
the DISENGAGED position.
forward.
Fig. 8B
WARNING:
7. If chain brake functions properly, turn the
stop, turn engine off and take your unit to
engine off and return the chain brake to
the nearest Authorized Service Center for
the DISENGAGED position.
service.
WARNING:
stop, turn engine off and take your unit to
the nearest Authorized Service Center for
D
Fig. 8D
service.
-- 8 -- -- 8 --
the starter rope rapidly
Fig. 8F
sure the
the starter
rapidly 4
Fig. 9
move
Fig. 9G
move
Activate the chain brake
Activate the chain brake
If chain does
If chain does
D
4
to
to
not
not