Deleting Pre-Programmed Positions; Settings/Adjustments; Setting The Type Of "Dry-Contact; Setting The Time Of Duration The Maneuver - Nice TTPRO BD Instrucciones Y Advertencias Para La Instalación Y El Uso

The roller shutter must move up: if it goes down, immediately press the button
04.
or to reverse the direction of movement.
At this point the procedure continues automatically: initially, TTPRO BD finds the
05. "0" position, by the caps, on opening; it then finds position "1", by the anti-
intrusion springs, on closing.
The motor emits 3 beeps (= end of the procedure) and the roller shutter closes
06.
fully.
07. Lastly, press the ON/OFF button to display the new settings.

3.5.3 - DELETING PRE-PROGRAMMED POSITIONS

• Deleting Position "0"
Press the button
: the LED on the button flashes.
01.
Press the button
02. : the LED on the button flashes.
RADIO
TEST
03. ➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
Once this operation terminates, the LED on the button
04.
• Deleting Position "1"
Press the button
: the LED on the button flashes.
01.
AUTO
Press the button
: the LED on the button flashes.
02.
RADIO
TEST
03. ➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
04. Once this operation terminates, the LED on the button
• Deleting position "I"
Press the button
: the LED on the button flashes.
01.
AUTO
Press the button
: the LED on the button flashes.
02.
RADIO
TEST
03. ➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
Once this operation terminates, the LED on the button
04.

3.6 - Settings/Adjustments

3.6.1 - SETTING THE TYPE OF "DRY-CONTACT"

Press the button : the current setting appears on the level LEDs.
01.
DRY
CONT.
Use the or button to turn on the LED that corresponds to the desired
02.
setting.
03.
➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
7 – English
AUTO
flashes.
flashes.
AUTO
flashes.
AUTO
Note: the number of
levels available and the
types of behaviour of
each dry-contact de-
pend on the connected
motor (refer to the motor
manual).

3.6.2 - SETTING THE TIME OF DURATION THE MANEUVER

Warning! - You can set the duration of the maneuver only if limit switches "0" and "1"
have already been set.
Press the button
01. If the operating time is not programmed, the LED flashes to indicate the closest
approximation, obtained from the motor speed setting.
AUTO
Use the or
02.
setting.
03. ➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
Note: the number of
available levels depends
on: the type of motor
connected, its maximum
and minimum speed
values and the positions
"0" and "1" stored.
Level LEDs Type of dry contact
1
2
3
4
5
6
7
8
: the current setting will appear on the level LEDs.
RDC
button to turn on the LED that corresponds to the desired
Examples of levels available for ERA INN
Level LEDs Maneuver time [sec]
1
2
3
4
5
6
7
8
9 (A1)
10 (A2)
11 (A3)
12 (A4)
13 (A5)
14 (A6)
15 (A7)
16 (A8)
DRY_1
DRY_2
DRY_3
DRY_4
DRY_5
DRY_6
DRY_7
DRY_8
5
7
10
15
20
25
30
35
40
50
60
70
80
90
100
110