Tabla de contenido
Idiomas disponibles
Idiomas disponibles
3.5.2 - PROGRAMMING OF POSITIONS
Motors with electronic limit switches have functions to programme the positions: "0"
(rolling shutter or awning all rolled up), "1" (rolling shutter or awning all unrolled) and "I"
(rolling shutter or awning in an intermediate position). If a position is already stored, the
corresponding LED will be lit, otherwise a short flash indicates that the position has not
been programmed.
3.5.2.A - Manual programming of positions "0", "1" and "I"
The positions must be stored in the following order: "0", "1" and "I".
The memorisation procedure may vary depending on the type of motor used. Therefore,
refer to the technical specifications which are also available on www.niceforyou.com
site, with details and specific examples for each type of motor.
• Programming position "0"
Use the
or
button to bring the roller shutter/awning to the "0" position
01.
desired.
Press the button
: the LED on the button flashes.
02.
03.
➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
When finished, the LED on the button
04.
Notes • The direction of movement associated with the button may be not correct until
position "1" is stored. • In some types of motors, changing position "0" could erase
positions "0" and "I".
• Programming position "1"
Use the
or
button to bring the roller shutter/awning to the "1" position
01.
desired.
Press the button
: the LED on the button flashes.
02.
AUTO
03.
➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
When finished, the LED on the button
04.
Note: changing position "1" erases position "I".
• Programming position "I"
Use the
or
button to bring the roller shutter/awning to the intermediate
01.
position "I" desired.
02.
Press the
button: the LED on the button flashes.
AUTO
03.
➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
When finished, the LED on the button
04.
Note: you cannot store position "I" if the "0" and "1" positions have not been stored
previously.
AUTO
turns on with a steady light.
AUTO
turns on with a steady light.
AUTO
turns on with a steady light.
AUTO
3.5.2.B - Automatic programming of positions "0" and "1"
In some motors for roller shutters, with electronic limit switches, there is a procedure
that automatically detects positions "0" and "1". If this feature is available, after TTPRO
switches on the LED on the button
AUTO
To perform this procedure there must be present on the application the caps on ascent
and/or burglar springs on descent. For more details refer to the motor instructions.
.
01.
Press the button
AUTO
02.
➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
03.
The motor emits 2 beeps (= start of the procedure).
The roller shutter must move up: if it goes down, immediately press the button
04.
or
to reverse the direction of movement.
At this point the procedure continues automatically: initially, TTPRO finds the "0"
05.
position, by the caps, on opening; it then finds position "1", by the anti-intrusion
springs, on closing.
The motor emits 3 beeps (= end of the procedure) and the roller shutter closes
06.
fully.
07.
Lastly, press the ON/OFF button to display the new settings.
3.5.3 - DELETING PRE-PROGRAMMED POSITIONS
• Deleting Position "0"
Press the button
: the LED on the button flashes.
01.
Press the button
02.
: the LED on the button flashes.
RADIO
TEST
03.
➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
Once this operation terminates, the LED on the button
04.
• Deleting Position "1"
Press the button
: the LED on the button flashes.
01.
AUTO
Press the button
: the LED on the button flashes.
02.
RADIO
TEST
03.
➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
04.
Once this operation terminates, the LED on the button
flashes.
AUTO
flashes.
flashes.
AUTO
AUTO
English – 6
Capítulos
Tabla de contenido
