Deleting Of The Parameters Stored In Ttpro Bd; Checking The Software Version; Updating The Ttpro Bd Firmware; Changing The Motor Address - Nice TTPRO BD Instrucciones Y Advertencias Para La Instalación Y El Uso

03. Press OK to launch the procedure.
04. When TTPRO BD transfers the data, the OK led flashes red rapidly.
05. When the procedure is complete, the green OK led is steady on.

3.8.3.1 - Deleting of the parameters stored in TTPRO BD

Press the button .
01.
RADIO
TEST
Press the following buttons in sequence:
with the led steady on can be selected, since the led indicates that the type of
02.
data is saved to the TTPRO BD; when selected, the respective led flashes).
03. Press OK to launch the procedure.
04. When TTPRO BD deletes the data, the OK led flashes red rapidly.
05. When the procedure is complete, the green OK led is steady on.

3.8.4 - CHECKING THE SOFTWARE VERSION

01. Press the OK button
➔ The green OK LED flashes: (within 3 sec) press the button
02.
03. The level LEDs show the version and revision of the software.
04. After 5 seconds TTPRO BD turns off automatically.

3.8.5 - UPDATING THE TTPRO BD FIRMWARE

If you need to update TTPRO BD (eg. the product software upgrade), contact the
01.
NICE technical support.

3.8.6 - CHANGING THE MOTOR ADDRESS

The address can only be modified if TTPRO BD is connected in TTBUS mode with
the dedicated cable.
Press the button : the actual motor address will start to flash on the level
F1 F2 F3
01.
LEDs.
02. Use Table 1 to select the new desired address.
03. Use buttons and to select the address you want to assign.
04. ➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
, , . (only the type of data
F1 F1 F2 F2 F3 F3
F1 F2 F3
.
F1 F2 F3
ADDRESS 1 2 3 4 5 6 7 8 A
Adr 0xFF 1 1 1 1 1 1 1 1 1
Adr 0
0 0 0 0 0 0 0 0 0
Adr 1 1 0 0 0 0 0 0 0 0
Adr 2 0 1 0 0 0 0 0 0 0
Adr 3 0 0 1 0 0 0 0 0 0
Adr 4 0 0 0 1 0 0 0 0 0
Adr 5
0 0 0 0 1 0 0 0 0
Adr 6 0 0 0 0 0 1 0 0 0
Adr 7 0 0 0 0 0 0 1 0 0
Adr 8 0 0 0 0 0 0 0 1 0
Adr 9 1 0 0 0 0 0 0 0 1
Adr 10
0 1 0 0 0 0 0 0 1
Adr 11 0 0 1 0 0 0 0 0 1
Adr 12 0 0 0 1 0 0 0 0 1
Adr 13 0 0 0 0 1 0 0 0 1
Adr 14 0 0 0 0 0 1 0 0 1
Adr 15
0 0 0 0 0 0 1 0 1
Adr 16
0 0 0 0 0 0 0 1 1
Adr > 16 0 0 0 0 0 0 0 0 1 flashing
4

BATTERY REPLACEMENT

TTPRO BD contains "AA" Ni-MH rechargeable batteries (they can be recharged using the
USB connection cable and a charger, or non-rechargeable 1.5 V AA batteries can be used.
TABLE 1
English – 10