Tabla de contenido
Idiomas disponibles
Idiomas disponibles
If no motor is found at the end of the search, TTPRO BD emits a brief beep and the
OK led turns steady RED.
3.3.3 - Forced motor scan
Press key
or key
for 1 second to force a scan for motors at the remain-
01.
ing addresses.
You can also change the scan mode (TTBUS - BD) by pressing key
02.
for 1 second at the end of each scan.
3.3.4 - Switching Off of TTPRO BD
01.
Press the ON/OFF key.
Release the button when TTPRO BD emits 1 beep and the RED LED starts to
02.
flash quickly.
TTPRO BD turns off automatically after 1 minute of inactivity.
3.4 - Transmitter programming
BUTTONS DEDICATED TO TRANSMITTERS
3.4.1 - Memorisation of the transmitter
Press and release the button
01.
ly, waiting to receive a transmitter.
(within 5 sec) Press and release any button on the transmitter to be memorised:
02.
➔ the LED on the button
flashes quickly.
➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
03.
3.4.2 - Deleting a single transmitter
Press and release the button
01.
ly, waiting to receive a transmitter.
Press and release the button
02.
transmitter.
(within 5 sec) Press and release any button on the transmitter to be deleted: ➔ the
03.
LED on the button
flashes quickly.
04.
➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
3.4.3 - Deleting all transmitters
Press and release the button
01.
ly, waiting to receive a transmitter.
5 – English
DRY
CONT.
: the LED above the button starts blinking slow-
DRY
CONT.
DRY
CONT.
: the LED above the button starts blinking slow-
DRY
CONT.
: the button starts blinking slowly waiting for a
RADIO
TEST
DRY
CONT.
: the LED above the button starts blinking slow-
DRY
CONT.
Hold down the key
02.
Led
remains steady on.
RADIO
TEST
03.
➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
3.4.4 - Memorising a single transmitter button (Mode 2)
Press and release the button
01.
or
ly, waiting to receive a transmitter.
On the transmitter (within 5 sec) press and release the button you want to
02.
store: On TTPRO BD ➔ LED on the button
Press and release the button
03.
desired command lights up (see the instruction manual of the motor connected
to TTPRO BD).
Press and release the button
04.
corresponding to the desired level lights up.
05.
➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
3.4.5 - Deleting a transmitter memorised in Mode 2
Press and release the button
01.
waiting to receive a transmitter.
Press and release the button
02.
waiting to receive a transmitter.
On the transmitter (within 5 sec) press and release the button on the transmit-
03.
ter to be deleted: On TTPRO BD ➔ LED on the button
➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
04.
If the transmitter is memorised in...
- Mode 2 = the procedure deletes only the button pressed.
- Mode 1 = the procedure deletes the transmitter, regardless of which button you press.
3.5 - Basic programming
3.5.1 - PROGRAMMING THE DIRECTION OF MOVEMENT
On motors with mechanical limit switch you can change the direction of movement as
follows.
If the direction is not programmed, the buttons
01.
movements of the motor; moreover, the LEDs above the buttons
flash at regular and much shorter intervals.
and release it when the led
RADIO
TEST
: the LED above the button starts blinking slow-
DRY
CONT.
flashes quickly.
and wait until the LED corresponding to the
F2
F3
F1
(or the button
) and wait until the LED
: the LED above the button starts blinking slowly,
DRY
CONT.
: the LED above the button starts blinking slowly,
RADIO
TEST
and
starts flashing quickly.
DRY
CONT.
DRY
CONT.
flashes quickly.
DRY
CONT.
will not control the
and
DRY
DRY
CONT.
CONT.
Capítulos
Tabla de contenido
