Tabla de contenido
Idiomas disponibles
Idiomas disponibles
General Safety Information
DeSCrIptIon
These Myers Stainless Steel Submersible Sump Pumps are
designed for drainage of sump pits and flooded basements,
dewatering flooded areas, and to provide laundry drainage.
Operates automatically. Has a 115V, 60 Hz., single phase,
permanent split capacitor motor. Pump casing, suction strainer,
impeller and shaft are all stainless steel. Permanently lubricated
ball bearings never need lubrication. Automatic thermal
overload protection. Equipped with a 15' 18/3 grounding-type
power cord and tethered float switch.
Non-clog cast stainless steel impeller, ceramic shaft facings, and
stainless steel oil chamber for seal lubrication.
SpeCIfICatIonS
Power supply required ............................................115V, 60 HZ.
Motor duty ................................................................Continuous*
Dedicated Circuit Requirement (minimum) ................... 15 Amps
Pump Discharge ....................................................... 1-1⁄4" MNPT
Discharge Adapter: ..........................................1-1⁄4" FNPT Elbow
Passes solids up to: ................................................................ 3/4"
*note: For continuous operation, water depth must be at
least 2".
UnpaCkInG anD InSpeCtIon
Handle with care. Check items received against packing list
to be sure that all equipment has been received. Inspect for
shipping damage. If found, file claim with carrier immediately.
General Safety InformatIon
reaD anD folloW
Safety InStrUCtIonS!
Electrically powered sump pumps normally give many years of
trouble-free service when correctly installed, maintained, and
used. However, unusual circumstances (interruption of power
to the pump, dirt/debris in the sump, flooding that exceeds the
pump's capacity, electrical or mechanical failure in the pump,
etc.) may prevent your pump from functioning normally. To
prevent possible water damage due to flooding, consult your
performanCe
model
DS33p1
DS50p1
DS75p1
SpeCIfICatIonS
model
Hp
DS33p1
1/3
DS50p1
1/2
DS75p1
3/4
1-1⁄4" MNPT-1-1⁄2" FNPT Adapter
Hp
5'
1/3
16.0
1/2
34.0
3/4
45.5
motor
full load
amps
rpm
2.8
3450
4.1
3450
6.4
3450
retailer about a secondary AC sump pump, a DC backup sump
pump, and/or a high water alarm. See the "Troubleshooting
Chart" in this manual for information about common sump
pump problems and remedies.
Know the pump application, limitations, and potential hazards.
Disconnect power before servicing.
Release all pressure within system before servicing any component.
Drain all water from system before servicing.
Secure discharge line before starting pump. An unsecured
discharge line will whip, possibly causing personal injury and/or
property damage.
Check hoses for weak or worn condition before each use,
making certain that all connections are secure.
Periodically inspect sump, pump, and system components. Keep
free of debris and foreign objects. Perform routine maintenance
as required.
Personal Safety:
1. Wear safety glasses at all times when working with pumps.
2. Keep work area clean, uncluttered, and properly lighted –
replace all unused tools and equipment.
3. Keep visitors at a safe distance from work area.
4. Make workshop child-proof – with padlocks, master
switches, and by removing starter keys.
When wiring an electrically driven pump, follow all electrical
and safety codes that apply.
this equipment is only for use on 115 volt (single phase)
and is equipped with an approved 3-conductor cord and
3-prong, grounding-type plug.
before servicing.
swimming pool areas. Pump is supplied with a grounding conductor
and grounding-type attachment plug. Be sure it is connected only to a
properly grounded grounding-type receptacle. Where a 2-prong wall
receptacle is encountered, it must be replaced with properly grounded
3-prong receptacle installed in accordance with codes and ordinances
that apply.
All wiring should be performed by a qualified electrician.
Make certain power source conforms to requirements of your
equipment.
Gpm of Water @ total feet of Head
10'
8.5
25.0
34.0
minimum
liquid
Circuit req.
temperature
(amps)
range
15
32°/120° F
15
32°/130° F
15
32°/130° F
to reduce risk of electric shock, pull plug
This pump has not been investigated for use in
15'
20'
1.0
–
15.5
7.0
21.5
12.0
Switch
Setting
on
off
12.0"
6.0"
12.0"
6.0"
12.0"
6.0"
2
Shutoff
16.0'
23.5'
26.2
pumps
Down
to
1-3/8"
1-3/8"
1-3/8"
Tabla de contenido
