Pump Specifications; Electrical Requirements - Xylem LOWARA Q-Smart Manual De Instalación, Funcionamiento Y Mantenimiento

en - Original instructions
quency
Rated input cur-
1
rent 12A
(Uin=230V)
Recommended
20A
2
line protection
Rated output
current 12 A
(Uin=230V)
Consumption in
(standby power may vary according
standby
to the type of sensor connected)
Type of load
Nominal Cosø
Box Self-extinguishing - grey
Frontal IP Pro-
tection
Connections
(use copper
(power supply, input and output)
conductor only)
Maximum input
power cable
section
Maximum motor
power cable
section
Pressure: 0 to 60 bar (0 to 6
3
Set point Level: 0 to 50 m (0 to 164 feet)
Temperature: -20 to 100°C (32
Ambient tem-
0 to 40°C (32 to 122°F)
perature
Ambient Humidi-
10 to 90% non-condensing
ty
4
Altitude
Alarm buzzer
Motor protection
fuse F1, F2
Auxiliary protec- 1A Time-Lag 5 x20 mm
tion fuse F3 (T1L 250V IEC60127-2/3)
5 multifunctional inputs for
Digital inputs NO/NC contact (voltage-free,
4 level electrode sensors,
Electric Probe
Sensitivity: 5 to 100kOhm,
inputs
Line capacity: 10nF max,
Electrode voltage: 6.5V - 20Hz
Transducer 0-20/4-20mA
(Sensor active value input)
Analogue input Current input 0-22 mA, accuracy
Sensor power supply +12 Vdc
1 Load relay
Digital outputs
Maximum current allowed for
the electric motor is 12A
Port for communication with the
TTL Serial port
supervision system via TTL with
34
24A
40A
2 x 12 A
1.8W
Electric motor
≥ 0.6
55
Screw terminal blocks
2
4 mm
2
4 mm
MegaPa)
to 122°F)
≤2000m asl
3.6kHz, Piezo
12 A (gG)
CH10
10.3x38 mm
12V, 4mA )
1 reference electrode
0.3%,
2 Load relays
30(15)A @ 250VAC
ModBus communication protocol
Signals: +5V, RX, TX, RTS, 0V
Port RJ45 for communication with
the card with voltage-free relays
RJ45 connector
Signals: +12V - 120mA , 0V,
6 open collector outputs
Dimensions and
Weight
1. The current supplied by the control panel shall
not be lower than the current absorbed by the
electric pumps, and depends also on the volt-
age drop due to the length of the cable.
2. Choose the current of the line protection de-
vice in relation to the maximum current ab-
sorbed by the motors.
3. Only if the electronic sensor is used.
4. For higher altitudes or other environmental
conditions not covered in this manual, please
contact your local After Sales / Service repre-
sentative.

Pump specifications

3.4
Refer to the user and maintenance manual of the
electric pump. It is essential to consider the limita-
tions of use of the control panel together with
those of the electric pump. See the
Technical data in Tab 1. The customer is respon-
sible for checking the limitations of the electric
pump if they are not specified in this manual.
4 Installation
Precaution
WARNING:
•
Observe the accident prevention
regulations in force.
•
Use suitable equipment and protec-
tive devices.
•
Always refer to the local regula-
tions, legislation and codes in force
regarding the selection of the instal-
lation site, plumbing and power
connection.

Electrical requirements

4.1
The local regulations in force overrule the specific
requirements given below.
Electrical connection checklist
Check that the following requirements are met:
•
The electrical leads are protected against high
temperature, vibrations and collisions.
•
The current type and voltage of the mains
connection must correspond to the specifica-
tions on the data plate on the pump.
•
It is recommended to provide electrical power
to the control panel with a dedicated power
line equipped with:
See Figure 3