Tabla de contenido
Idiomas disponibles
Idiomas disponibles
CUTTING WIDTH: 132 cm.
HOURLY MOWING CAPACITY: 12.000 m²/h (± 2.5 acres).
ATTACHMENTS: 1320 mm (± 52 in) cutting deck with collection and mulching kit (weight 170 kg), 160 cm (63")
cutting deck LMP (side discharge – rear discharge – mulching) dimension with baffle 192 cm (76"), weight 170 kg.
130 cm ( 50") cutting deck MP (rear discharge-mulching with quick shift lever) dimension 132 cm ( 52"), weight 150
kg. All purpose flail 135 cm (60") with scarifier kit. Snow blade 150 cm, comfort cabin with heating, snow chains for
front wheels.
SIZE (with cutting deck) Length: 3250 mm (± 128 in) Width: 1410 mm (± 52 in) Height: 1750mm (± 68.9 in)
GROUND CLEARANCE: 150 mm (± 5.9 in)
DISTANCE BETWEEN AXLES: 1230 mm (± 48.4 in)
WEIGHT (without cutting deck): 995 kg (±2195 lbs)
WEIGHT (with cutting deck): 1220 kg (±2564 lbs)
-
Make sure the machine is complete and that it has not been damaged during transport.
-
Check the levels of the engine oil (fig. 14, ref. C) and hydrostatic transmission (fig. 4).
-
Check the tyre pressures:
Front wheels 23×12.00 – 12 (1.4 bar)
Rear wheels 18×8.50 – 8 (1.4 bar)
Deck wheels (1.5 bar)
-
Check the battery voltage, it must not be less than 12.5 Volts; recharge if necessary.
-
If a dry battery has been supplied with separate acid, to put the machine into service proceed as follows:
1) pour in the acid and wait 2 hours;
2) charge the battery with a charger set to 12 Volts on a slow charge for 2 hours.
Caution, if this procedure is not observed this could lead to the battery deteriorating and the acid leaking out
during work.
BATTERY
Caution! The gases released by the battery are explosive, so keep it away from naked flames or sparks. Check the
level of the liquid at regular intervals and keep the terminals greased with Vaseline. Important:
Do not invert the battery poles.
-
-
Do not run the lawnmower without the battery, as it is equipped with a charge regulator.
-
Be careful not to cause any short circuits.
RUNNING IN – CAUTION!!
Change the engine oil and filter after the first 50 hours of work. Check for oil leaks or loose screws, especially those
that retain the blades and the wheels. Adjust the tension on the PTO belts with the nut located on the spring: the
spring has to be adjusted at 75 mm of length (see red arrow) (fig. 5, ref. A). Adjust the loading accelerator belt
tension with the nut located on the spring: the spring has to be adjusted at 70 mm of length (see red arrow) (fig. 6,
ref. B).
Before turning on the engine always check that:
-
the radiator liquid is up to the level (fig. 7);
-
the engine cooling intake grids are clear (fig. 8);
the engine oil is up to the level (fig. 14, ref. C);
-
-
the hydraulic oil is up to the level (fig. 4);
-
the forward and reverse pedals (fig. 1 n° 1 e n°2) are in the stop position;
-
the PTO button is in the neutral position (fig. 1 n°27);
-
the air filter is clean (fig. 9);
-
the grid inside the grass catcher is clean (fig. 10); to take it out, put in the cover safety block (fig. 17) and act on
the lever (fig. 10, ref. B);
-
the cutting deck, the loading accelerator and the grass entry ducts are clean.
Fill the fuel tank with fuel (diesel oil) using a funnel fitted with a very fine mesh filter (fig. 7).
Translation of the original instructions
PUTTING THE MACHINE INTO SERVICE
INSTRUCTIONS FOR USE
8
Tabla de contenido
