Spark Arrester; Idle Speed; Helpful Tips & Suggestions; Storing Your Engine - Honda GX270 Manual Del Propietário

3RZ7E6000.fm 13 ページ ２０１２年１１月２０日 火曜日 午後２時３９分
SPARK ARRESTER (applicable types)
In Europe and other countries where the machinery directive 2006/
42/EC is enforced, this cleaning should be done by your servicing
dealer.
The spark arrester may be standard or an optional part, depending
on the engine type. In some areas, it is illegal to operate an engine
without a spark arrester. Check local laws and regulations. A spark
arrester is available from your servicing dealers.
The spark arrester must be serviced every 100 hours to keep it
functioning as designed.
If the engine has been running, the muffler will be hot. Allow it to
cool before servicing the spark arrester.
Spark Arrester Removal
1. Remove the two 8 mm nuts and remove the muffler from the
cylinder.
2. Remove the four 5 mm screws and 6 mm screw (applicable
type) from the muffler protector and remove the muffler
protector.
3. Remove the 4 mm screw from the spark arrester, and remove
the spark arrester from the muffler.
6 mm SCREW
(applicable type)
MUFFLER PROTECTOR
5 mm SCREWS
MUFFLER
8 mm NUTS
Spark Arrester Cleaning & Inspection
1. Use a brush to remove carbon
deposits from the spark arrester
screen. Be careful not to damage
the screen. Replace the spark
arrester if it has breaks or holes.
2. Install the spark arrester, muffler protector and muffler in the
reverse order of disassembly.
5 mm SCREWS
MUFFLER PROTECTOR
4 mm SCREW

SPARK ARRESTER

SCREEN
ENGLISH

IDLE SPEED

Adjustment
1. Start the engine outdoors, and
allow it to warm up to
operating temperature.
2. Move the throttle lever to its
minimum position.
3. Turn the throttle stop screw to
obtain the standard idle speed.
Standard idle speed:
1,400±150 rpm
HELPFUL TIPS & SUGGESTIONS

STORING YOUR ENGINE

Storage Preparation
Proper storage preparation is essential for keeping your engine
trouble-free and looking good. The following steps will help to keep
rust and corrosion from impairing your engine's function and
appearance, and will make the engine easier to start when you use
it again.
Cleaning
If the engine has been running, allow it to cool for at least half an
hour before cleaning. Clean all exterior surfaces, touch up any
damaged paint, and coat other areas that may rust with a light film
of oil.
Using a garden hose or pressure washing equipment can force
water into the air cleaner or muffler opening. Water in the air
cleaner will soak the air filter, and water that passes through the
air filter or muffler can enter the cylinder, causing damage.
Fuel
Depending on the region where you operate your equipment, fuel
formulations may deteriorate and oxidize rapidly. Fuel deterioration
and oxidation can occur in as little as 30 days and may cause
damage to the carburetor and/or fuel system. Please check with
your servicing dealer for local storage recommendations.
Gasoline will oxidize and deteriorate in storage. Deteriorated
gasoline will cause hard starting, and it leaves gum deposits that
clog the fuel system. If the gasoline in your engine deteriorates
during storage, you may need to have the carburetor and other fuel
system components serviced or replaced.
The length of time that gasoline can be left in your fuel tank and
carburetor without causing functional problems will vary with such
factors as gasoline blend, your storage temperatures, and whether
the fuel tank is partially or completely filled. The air in a partially
filled fuel tank promotes fuel deterioration. Very warm storage
temperatures accelerate fuel deterioration. Fuel deterioration
problems may occur within 30 days from keeping the fuel in the
fuel tank, or even less if the gasoline was not fresh when you filled
the fuel tank.
Fuel system damage or engine performance problems resulting
from neglected storage preparation are not covered under the
Warranty.
THROTTLE STOP SCREW
13