Idiomas disponibles
Idiomas disponibles
WARNING
Danger of injury!
Remove the battery from the power tool before carrying
out any work on the power tool (e.g. maintenance, tool
change, etc.) and when transporting and storing it.
There is a risk of injury if the on/off switch is operated
unintentionally.
8.1
Fitting the protective cover (12)
(Fig. 2)
1. Slide the protective cover (12) into the recesses on
the motor head (15).
The protective cover (12) clicks into place audibly.
2. Screw the protective cover (12) tight with the Phillips
screw (12a).
Use the Phillips screwdriver included in the scope of
delivery.
8.2
Fitting the spacer bar (13) (Fig. 1)
Note:
The spacer bar keeps plants and stems that cannot be
cut away from the cutting device.
1. Fit the spacer bar (13) to the front of the motor head
(15).
8.3
Fitting the spacer roller (11)
(Fig. 3, 8)
Lawn edge trimming:
1. Attach the spacer roller (11) to the motor head (15).
It engages audibly.
Cutting grass / transporting the product:
1. Attach the spacer roller (11) to the protective cover
(12).
You will hear it click into place.
9
Operation
The hand-held and portable cordless strimmer has a cut-
ting device with a thread coil with fully automatic adjust-
ment. The product is also equipped with an adjustable tilt
angle, adjustable telescopic tube and a spacer bar. To
protect the user, the product is fitted with a protective cov-
er that covers the cutting device.
WARNING
Danger of injury!
Remove the battery from the power tool before carrying
out any work on the power tool (e.g. maintenance, tool
change, etc.) and when transporting and storing it.
There is a risk of injury if the on/off switch is operated
unintentionally.
WARNING
Check the safety equipment regularly before each start-
up. Faulty safety equipment can cause serious injuries!
ATTENTION
Make sure that the ambient temperature does not ex-
ceed 50°C and does not fall below -20°C during work.
ATTENTION
The product is part of the 20V IXES series and may on-
ly be operated with batteries of this series. Batteries
may only be charged with battery chargers of this se-
ries. Observe the manufacturer's instructions.
9.1
Inserting/removing the battery (19)
into/from the battery mount (8)
(Fig. 4)
Inserting the battery
1. Push the battery (19) into the battery mount (8). The
battery (19) clicks into place audibly.
Removing the battery
1. Press the unlock button (20) of the battery (19) and
remove it from the battery mount (8).
9.2
Switching the product on/off
(Fig. 1)
Switching on
Notes:
Before switching on, make sure that the product does not
touch any objects.
Note:
• Always hold the product tight with both hands
during work. Make sure that you have a secure foot-
ing.
• Remain attentive at all times when working, and keep
third parties at a safe distance from your work area.
1. To switch on, press the switch lock (2) and then press
the on/off switch (9).
Note:
It is not necessary to keep the switch lock pressed after
starting the product. The switch lock is intended to pre-
vent accidental starting of the product.
Switching off
1. To switch off, release the on/off switch (9).
Continuous operation is not possible.
CAUTION
After switching off, the product will run on. Wait until the
product has come to a complete stop.
9.3
Overload protection
Note:
In the event of overloading, the motor will switch itself off.
After a cool-down period (time varies) the motor can be
switched back on again.
9.4
Settings on the product
9.4.1
Notes:
You can move the additional handle to various different
positions.
Adjust the additional handle so that the coil capsule is tilt-
ed slightly forwards in the working position.
www.scheppach.com
Adjusting the additional handle (3)
(Fig. 5)
GB | 19
