Idiomas disponibles
Idiomas disponibles
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Before
you move your
refrigerator
into its final
location,
it is
important
to make sure you have the proper
electrical
connection.
Recommended
Grounding
Method
A 115 volt, 60 Hz, AC only 15- or 20-amp
fused, grounded
electrical
supply is required.
It is recommended
that a separate
circuit serving only your refrigerator
and approved
accessories
be provided.
Use an outlet that cannot be turned off by a
switch. Do not use an extension cord.
NOTE: Before performing
any type of installation,
cleaning, or
removing a light bulb, turn Cooling OFF, and then disconnect
the refrigerator
from the electrical
source. When you have
finished, reconnect the refrigerator
to the electrical
source and
turn Cooling ON. See "Using the Control(s)."
A cold water
supply
with water
pressure
between
30 and
120 psi (207
and 827
kPa) is required
to operate
the water
dispenser
and ice maker.
If you have questions
about
your water
pressure,
call
a licensed,
qualified
plumber.
Reverse
Osmosis
Water
Supply
IMPORTANT:
The pressure
of the water
supply
coming
out of a
reverse
osmosis
system going
to the water
inlet valve
of the
refrigerator
needs to be between
30 and 120 psi (207
and
827 kPa).
If a reverse
osmosis water
filtration
system
is connected
to your
cold water
supply,
the water
pressure
to the reverse
osmosis
system
needs to be a minimum
of 40 to 60 psi (276 to 414 kPa).
If the water
pressure
to the reverse
osmosis
system
is less than
40 to 60 psi (276 to 414 kPa):
•
Check
to see whether
the sediment
filter
in the reverse
osmosis
system
is blocked.
Replace
the filter
if necessary.
•
Allow
the storage
tank on the reverse
osmosis system
to refill
after
heavy
usage.
The tank
capacity
could
be too low to
keep
up with
the requirements
of the refrigerator.
If your
refrigerator
has a water
filter,
it may further
reduce
the water
pressure
when used in conjunction
with
a reverse
osmosis
system.
Remove
the water
filter.
See '"Water
Filtration
System."
If you have questions about your water pressure, call a licensed,
qualified
plumber.
Co s ; ec :he
Su s s v
Read all directions
before
you begin.
IMPORTANT:
•
If you turn the refrigerator
on before
the water
line is
connected,
turn the ice maker
OFF.
Tools Needed;
Gather
the required
tools and parts
before
starting
installation.
Read and follow
the instructions
provided
with
any tools listed
here.
•
Flat-blade
screwdriver
•
1/4" Nut driver
•
7/16" and 1/2" Open-end
or two
•
1/4" Drill
bit
adjustable
wrenches
•
Cordless
drill
NOTE:
Your refrigerator
dealer
has a kit available
with
a 1/4"
(6.35
mm) saddle-type
shutoff
valve,
a union,
and copper
tubing.
Before
purchasing,
make
sure a saddle-type
valve
complies
with
your
local
plumbing
codes.
Do not use a piercing-
type
or 3/16" (4.76
mm) saddle
valve
which
reduces
water
flow
and clogs
more easily.
Connect to Water Line
Style 1
1.
Unplug
refrigerator
or disconnect
power.
2.
Turn OFF main water
supply.
Turn ON
nearest
faucet
long
enough
to clear
line of water.
3.
Locate
a Y2" to 11/4 '' (1.25 cm to 3.18 cm) vertical
cold
water
pipe
near the refrigerator.
IMPORTANT:
4°
Make
sure it is a cold
water
pipe.
Horizontal
pipe
will work,
but drill on the top side of the
pipe,
not the bottom.
This will help keep water
away
from
the drill and normal
sediment
from
collecting
in the
valve.
Determine the length of copper tubing you need. Measure
from the connection on the lower left rear of refrigerator
to
the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use
Y4" (6.35 mm) O.D. (outside diameter)
copper tubing. Be
sure both ends of copper tubing are cut square.
