Special Functions; Deleting The Memory - Nice Hyke HK7024 Instrucciones Y Advertencias Para La Instalación Y El Uso

L7 Mainte- L1
nance
L2
warning
L3
L4
L5
L6
L7
L8
L8 List of L1
faults
L2
L3
L4
L5
L6
L7
L8
Note – The factory settings are highlighted in grey.
01. Press and hold down the "Set" key for approx. 3 seconds.;
02. Release the key when LED "L1" starts flashing;
03. Press the " " or " " key to move the flashing LED to the LED representing the "input LED" of the parameter to be modified;
04. Press and hold the "Set" key through to completion of point 06;
05. Wait approx. 3 seconds, until the LED representing the current level of the parameter to be modified illuminates;
06. Press keys " " or " " to move the LED representing the value of the parameter;
07. Release the "Set" key;
08. Wait 10 seconds (maximum time) to exit the programming mode.
Note – During this procedure, points 03 to 07 need to be repeated when programming other parameters during the phase itself.

6.3 - Special functions

6.3.1 - Function: "Move anyway"
This function allows the automation to be operated even when any of the safe-
ty devices does not work correctly or is out of use.
The automation can be controlled in the "hold-to-run" mode. Proceed as follows:
01. Send a command to operate the gate using a transmitter or a key selector,
etc. If everything operates correctly, the gate will move normally, otherwise
proceed as follows;
02. within 3 seconds, activate the control again and keep it activated;
03. after approximately 2 seconds, the gate will perform the required move-
ment in "hold-to-run" mode; i.e. the gate will continue to move only as long
as the control is activated.
If the safety devices do not operate, the flashing light flashes a few times to indi-
cate the kind of problem (see chapter 6 - Table 8).
6.3.2 - Function: "Maintenance warning"
This function serves to indicate when the automation requires maintenance.
The maintenance warning signal is given by way of a lamp connected to the
S.C.A. (open gate light) output when this output is programmed as "Mainte-
nance light". The various warning lamp signals are shown in Table 7.
To program the limit value of the maintenance operations, see Table 5.
Table 7 - "Maintenance light"
Number of manoeuvres Signal
Below 80% of the limit Light on for 2 seconds at the start of the opening
manoeuvre.
Between 81% and Light flashing for the entire duration of the manoeuvre.
100% of the limit
Beyond 100% of the limit Light flashing continuously.
500
1000
1500
2500
5000
10000
15000
20000
Manoeuvre 1 result (most recent)
Manoeuvre 2 result
Manoeuvre 3 result
Manoeuvre 4 result
Manoeuvre 5 result
Manoeuvre 6 result
Manoeuvre 7 result
Manoeuvre 8 result
TABLE 6 - Programming procedure (second level functions)

6.4 - Deleting the memory

To delete the control unit memory and restore all factory settings, proceed as
follows:
press and hold keys " " and " " until leds L1 and L2 start flashing.
7 WHAT TO DO IF...
(troubleshooting guide)
Some devices are able to emit signals that serve to recognise their state of
operation or possible faults.
If a flashing light is connected to the FLASH output on the control unit, it will
flash at intervals of 1 second during a manoeuvre. If faults occur, the flashing
light will emit a sequence of two shorter flashes separated by a 1 second
pause. Table 8 shows the cause and solution for each type of signal.
The LEDs on the control unit also emit signals.
Table 9 shows the cause and solution for each type of signal.
It is possible to verify faults that have occurred during the last 8 manoeuvres.
See Table 10.
Controls the number of manoeuvres:
when this number is exceeded, the
control unit signals an automation
maintenance request; see paragraph
6.3.2. – Maintenance warning.
The type of fault that has occurred in
the last 8 manoeuvres can be establi-
shed
See TABLE 10 – Fault log.
SET
3 s
L1
SET
o
SET
or
SET
10 s
English – 9