Scheppach Compact 15t Traduccion Del Manual De Instrucciones Originale página 44

9.5 Mounting the protective frame (16) (Fig. 9)
1. Push the bars of the protective frame (16) into the
mounts (16a).
2. Insert the hexagonal bolts M8x50mm (16b) with a
washer through each of the holes.
3. Secure the hexagonal bolts M8x50mm (16b) with
one washer and one locknut each. Use two 13mm
open-ended spanners / socket spanners.
4. Fit the second protective bar (16) in the same way.
9.6 Fitting the supports (12) (Fig. 9)
1. Take the supports (12) and fix them to the base
plate (11) with the M10x25mm hexagonal bolts
(12a) and a washer for each. Use a 16mm
open-ended spanner / socket spanner.
9.7 Fitting the chain hook (22) (Fig. 10a)
1. Mount the chain hook (22) to the holder on the
splitting column (2) with two hexagon bolts
M12x40mm (22a), washers and lock nuts. Use two
19mm open-ended spanners / socket spanners.
9.8 Fitting the trunk lifter (7) (Fig. 10)
Note: The chain of the trunk lifter may only be
attached to the chain hook using the last link for
safety reasons.
1. Mount the log lifter (7) with a hexagon bolt
M12x70mm (7a), washer and lock nut to the hold-
er of the base plate (11), the lock nut must be on
the right side (towards the wheels)! Use two 19mm
open-ended spanners / socket spanners.
2. Slide the log lift support (10) into the recess. Fix
the log lift support (10) with a hexagon socket
screw M6x10mm (10a).
3. Attach the chain (28) to the log lifter (7) in the
following order: Hexagon bolt M12x40mm (28a),
washer, log lifter bracket (7b), washer, chain
(28), washer and lock nut. Screw on the lock nut
only so far that the chain (28) can move freely.
Attention! The chain (28) must turn completely
smoothly on the hexagon head screw M12x40mm
(28a)!
4. Hang the end of the chain in the chain hook (22).
9.9 Fitting the trunk lifter lock (26) (Fig. 11)
1. Mount the lever (27) with a hexagon bolt M8x55mm
(26a), washer and lock nut to the trunk lift lock (26).
Use two 13mm open-ended spanners / socket
spanners.
2. Slide the trunk lift latch (26) into the holder.
44 | GB
3. Insert the hexagonal bolts M8x55mm (26b) with a
washer through each of the holes.
4. Secure the hexagonal bolts M8x55mm (26b) with
one washer and one locknut each. Use two 13mm
open-ended spanners / socket spanners.
5. Check the ease of the lever (27).
10. Before commissioning
m Attention!
Always make sure the product is fully assembled
before commissioning!
m Attention!
Before performing setting or maintenance work,
unplug the mains plug!
m WARNING!
Health hazard!
Inhalation of oil vapours and exhaust gases can cause
serious damage to health, unconsciousness and in ex-
treme cases death.
- Do not breathe in oil vapours and exhaust gases.
- Operate the device outdoors only.
NOTE!
Product damage
If the product is operated without or with too little hy-
draulic oil, this can lead to hydraulic pump damage.
NOTE!
Environmental damage!
Spilled oil can pollute the environment permanently.
The liquid is highly toxic and can quickly lead to water
pollution.
- Fill/empty oil only on level, paved surfaces.
- Use a filling nozzle or funnel.
- Collect drained oil in a suitable container.
- Wipe up spilled oil carefully immediately and dis-
pose of the cloth according to local regulations.
- Dispose of oil as per local regulations.
Before each use, always check:
• the connection cables for defective areas (cracks,
cuts and the like),
• The device for possible damage,
• whether all screws are tightened,
• The hydraulic system for leaks,
• The oil level
• The safety devices and
• the ON/OFF switch.
www.scheppach.com