Idiomas disponibles
Idiomas disponibles
j)
Ensure the mitre saw is mounted or placed on
a level, firm work surface before use. A level
and firm work surface reduces the risk of the mitre
saw becoming unstable.
k)
Plan your work. Every time you change the
bevel or mitre angle setting, make sure the ad-
justable fence is set correctly to support the
workpiece and will not interfere with the blade
or the guarding system. Without turning the tool
"ON" and with no workpiece on the table, move
the saw blade through a complete simulated cut
to assure there will be no interference or danger of
cutting the fence.
l)
Provide adequate support such as table exten-
sions, saw horses, etc. for a workpiece that is
wider or longer than the table top. Workpiec-
es longer or wider than the mitre saw table can
tip if not securely supported. If the cut-off piece
or workpiece tips, it can lift the lower guard or be
thrown by the spinning blade.
m) Do not use another person as a substitute for
a table extension or as additional support. Un-
stable support for the workpiece can cause the
blade to bind or the workpiece to shift during the
cutting operation pulling you and the helper into
the spinning blade.
n)
The cut-off piece must not be jammed or
pressed by any means against the spinning
saw blade. If confined, i.e. using length stops, the
cut-off piece could get wedged against the blade
and thrown violently.
o)
Always use a clamp or a fixture designed to
properly support round material such as rods
or tubing. Rods have a tendency to roll while be-
ing cut, causing the blade to "bite" and pull the
work with your hand into the blade.
p)
Let the blade reach full speed before contact-
ing the workpiece. This will reduce the risk of the
workpiece being thrown.
q)
If the workpiece or blade becomes jammed,
turn the mitre saw off. Wait for all moving
parts to stop and disconnect the plug from the
power source and/or remove the battery pack.
Then work to free the jammed material.
Continued sawing with a jammed workpiece could
cause loss of control or damage to the mitre saw.
r)
After finishing the cut, release the switch, hold
the saw head down and wait for the blade to
stop before removing the cut-off piece. Reach-
ing with your hand near the coasting blade is dan-
gerous.
s)
Hold the handle firmly when making an incom-
plete cut or when releasing the switch before
the saw head is completely in the down posi-
tion. The braking action of the saw may cause the
saw head to be suddenly pulled downward, caus-
ing a risk of injury.
Warning! This electric tool generates an electromag-
netic field during operation. This field can impair active
or passive medical implants under certain conditions.
In order to prevent the risk of serious or deadly injuries,
we recommend that persons with medical implants
consult with their physician and the manufacturer of
the medical implant prior to operating the electric tool.
Safety Instructions for the handling of saw blades
1
Do not use damaged or deformed saw blades.
2
Do not use any insertion tools with cracks. Sort out
cracked insertion tools. Repairs are not permitted.
3
Do not use saw blades made of high speed steel.
4
Check the condition of the saw blades before using
the multifunction sliding cross cut mitre saw.
5
Make sure that a suitable saw blade for the mate-
rial to be cut is selected.
6
Only use saw blades recommended by the man-
ufacturer.
Saw blades designed to cut wood and similar ma-
terials must comply with EN 847-1.
7
Do not use saw blades made of high-speed alloy
steel (HSS steel).
8
Only use saw blades for which the maximum per-
missible speed is not lower than the maximum
spindle speed of the multifunction sliding cross
cut mitre saw and which are suitable for the ma-
terial to be cut.
9
Observe the saw blade direction of rotation.
10 Only insertion the saw blade if you have mastered
their use.
11 Observe the maximum speed. The maximum
speed specified on the insertion tool may not be
exceeded. If specified, observe the speed range.
12 Clean grease, oil and water off of the clamping
surfaces.
13 Do not use any loose reducing rings or bushes for
the reducing of holes on saw blades.
14 Make sure that fixed reducer rings for securing the
insertion tool have the same diameter and have at
least 1/3 of the cutting diameter.
15 Make sure that fixed reducer rings are parallel to
each other.
www.scheppach.com
GB | 29
