Support For Long Pieces - DeWalt DWS780 Manual De Instrucciones

ENGlIsH
If you cannot secure the workpiece on the table and against the fence by hand, (irregular shape,
etc.) or your hand would be less than 4" (100 mm) from the blade, a clamp or other fixture must
be used.
For best results use the vertical material clamp
clamps can be purchased at your local retailer or D
Other aids such as spring clamps, bar clamps or C-clamps may be appropriate for certain sizes
and shapes of material. Use care in selecting and placing these clamps. Take time to make a dry
run before making the cut. The left fence will slide from side to side to aid in clamping
To Install Clamp (Fig. A)
1. Insert it into the hole behind the fence
the miter saw. The groove on the clamp rod should be fully inserted into the base. Ensure this
groove is fully inserted into the base of the miter saw. If the groove is visible, the clamp will
not be secure.
2. Rotate the clamp 180º toward the front of the miter saw.
3. Loosen the knob to adjust the clamp up or down, then use the fine adjust knob to firmly
clamp the workpiece.
NoTE: Place the clamp on the opposite side of the base when beveling. ALWAYS MAKE DRY
RUNS (UNPOWERED) BEFORE FINISH CUTS TO CHECK THE PATH OF THE BLADE. ENSURE THE
CLAMP DOES NOT INTERFERE WITH THE ACTION OF THE SAW OR GUARDS.

Support for Long Pieces


WARNING: To reduce the risk of serious personal injury, turn off the tool and
disconnect it from the power source before attempting to move it, change
accessories or make any adjustments.
ALWAYS SUPPORT LONG PIECES.
Never use another person as a substitute for a table extension; as additional support for a
workpiece that is longer or wider than the basic miter saw table or to help feed, support or pull
the workpiece.
For best results, use the DW7080 extension work support to extend the table width of your saw,
available from your dealer at extra cost.
Support long workpieces using any convenient means such as sawhorses or similar devices to
keep the ends from dropping.
Cutting Picture Frames, Shadow Boxes And Other Four-Sided
Projects (Fig. P, Q)
To best understand how to make the items listed here, we suggest that you try a few simple
projects using scrap wood until you develop a "feel" for your saw.
Your saw is the perfect tool for mitering corners like the one shown in Figure P. Sketch 1 in
Figure Q shows a joint made by using the bevel adjustment to bevel the edges of the two boards
at 45º each to produce a 90º corner. For this joint the miter arm was locked in the zero position
and the bevel adjustment was locked at 45º. The wood was positioned with the broad flat side
against the table and the narrow edge against the fence. The cut could also be made by mitering
right and left with the broad surface against the fence.
Fig. P
Cutting Trim Molding And Other Frames (Fig. Q)
Sketch 2 in Figure Q shows a joint made by setting the miter arm at 45º to miter the two boards
to form a 90º corner. To make this type of joint, set the bevel adjustment to zero and the miter
arm to 45º. Once again, position the wood with the broad flat side on the table and the narrow
edge against the fence.
The two sketches in Figure Q are for four-sided objects only.
As the number of sides changes, so do the miter and bevel angles. The chart below gives the
proper angles for a variety of shapes.
– EXAMPLES –
NUMBER OF SIDES
4
5
6
7
8
9
10
38
21 provided with your saw. Additional DW7082
WALT service center.
e
. The clamp should be facing toward the back of
10
Fig. Q
1
1
MITER OR BEVEL ANGLE
45°
36°
30°
25.7°
22.5°
20°
18°
The chart assumes that all sides are of equal length. For a shape that is not shown in the chart,
use the following formula: 180º divided by the number of sides equals the miter (if the material is
cut vertically) or bevel angle (if the material is cut laying flat).
Cutting Compound Miters (Fig. R)
A compound miter is a cut made using a miter angle and a bevel angle at the same time. This is
the type of cut used to make frames or boxes with slanting sides like the one shown in Figure R.
NoTE: If the cutting angle varies from cut to cut, check that the bevel lock knob and the miter
lock handle are securely locked. These must be locked after making any changes in bevel
or miter.
The chart at the end of this manual (Table 1) will assist you in selecting the proper bevel and
miter settings for common compound miter cuts. To use the chart, select the desired angle A
(Fig. R) of your project and locate that angle on the appropriate arc in the chart. From that point
follow the chart straight down to find the correct bevel angle and straight across to find the
correct miter angle.
Fig. R
Set your saw to the prescribed angles and make a few trial cuts. Practice fitting the cut pieces
together until you develop a feel for this procedure and feel comfortable with it.
Example: To make a 4-sided box with 26º exterior angles (Angle A, Fig. R), use the upper right
arc. Find 26° on the arc scale. Follow the horizontal intersecting line to either side to get miter
angle setting on saw (42°). Likewise, follow the vertical intersecting line to the top or bottom to
get the bevel angle setting on the saw (18°). Always try cuts on a few scrap pieces of wood to
verify the settings on the saw.
Cutting Base Molding (Fig. S)
ALWAYS MAKE A DRY RUN WITHOUT POWER BEFORE MAKING ANY CUTS.
Straight 90° cuts:
Position the wood against the fence and hold it in place as shown in Figure S. Turn on the saw,
allow the blade to reach full speed and lower the arm smoothly through the cut.
Fig. S
2
Cutting Base Molding up to 6.75" (171 mm) Vertically Against
the Fence (Fig. K, S)
NoTE: Use the slide lock lever, shown in Figure K, when cutting base molding measuring from 3"
to 6.75" (76 mm to 171 mm) high vertically against the fence.
Position material as shown in Figure S.
All cuts should be made with the back of the molding against the fence and with the bottom of
the molding against the table.
• Miter left 45°
Left side
• Save left side of cut
• Miter right 45°
Right side
• Save right side of cut
Material up to 6.5" (165 mm) can be cut as described above.
Cutting Crown Molding
Your miter saw is better suited to the task of cutting crown molding than any tool made. In order
to fit properly, crown molding must be compound mitered with extreme accuracy.
The two flat surfaces on a given piece of crown molding are at angles that, when added together,
equal exactly 90°. Most, but not all, crown molding has a top rear angle (the section that fits flat
against the ceiling) of 52° and a bottom rear angle (the part that fits flat against the wall) of 38°.
aNGlE "a"
Inside corner outside corner
• Miter right 45°
• Save left side of cut
• Miter left 45°
• Save right side of cut