Grillo FX27 Zero turning Manual De Instrucciones página 9

STARTING THE ENGINE
Insert the ignition key (fig. 1, n°3) and turn it until the engine oil indicator light is on. Push the throttle
lever to the end in order to automatically start the STARTER (fig.1, n. 6). As soon as the engine starts,
release the key and bring the throttle lever back to reach again the engine max. revs. To switch the
engine off turn the key to the "STOP" position.
STARTING WORK
1) Adjust the cutting height using the switch on the dashboard (fig. 1, n°4).
2) Adjust the seat (fig. 1, n°14) and the levers positions (fig.1, n°7).
3) Accelerate the engine half-way (fig. 1, n°6). Do not engage the blades with the engine at
maximum speed. Move the steering levers from the rest to the work position; in this way, the parking
brake will disengage and the machine can move. Now it is possible to engage the PTO by lifting the
appropriate switch (fig. 1, n°2). Always engage the blades some metres before getting into the grass
to cut, so to make sure the cutting deck get cleaned.
4) Bring the engine to its full speed.
5) Gently operate the steering levers (fig. 1, n°1) and start work.
6) If you want to get from "rear discharge" mode to "mulching" and vice versa, disengage the PTO (fig. 1,
n°2) and move the steering levers to the parking brake position (fig. 1, n°1). Grip the appropriate lever
(fig.8, ref.A) making sure you are lifting the corresponding position lock (fig. 8, ref.B). Turn the lever in the
working mode you need. Free the position lock until it embeds in its grooved swaging (fig. 9, ref.A).
FINISHING WORK
Once mowing has been completed, disengage the blades. To stop:
1) Move the steering levers to the parking brake position (fig. 1, n°1).
2) Set the throttle lever to minimum speed (fig. 1, n°6).
3) Turn the engine off by turning the key in the "STOP" position (fig. 1, n°3).
GUIDELINES FOR EFFECTIVE USE
The machine can also be used under most demanding conditions. Certain measures must be taken and
all devices must be adjusted properly.
1) Before starting work check that the deck is perfectly clean without any dried grass or soil crusting.
2) Check the terrain before mowing, make sure there are no stones, sticks of foreign objects.
3) While mowing keep the engine at maximum revs., adjust the speed to suit the height of the grass.
Be careful when coming across tall thick clumps of grass, slow down.
4) Sharpen the lawnmower blades regularly; the cut will be better and the engine will not have to work
so hard (fig. 22, ref.A)
5) After disengaging the PTO, engage the blades some metres before getting into the grass to cut, so
the cutting deck is cleaned and the clutch is protected.
6) Keep the grid on the engine clean (fig. 4, ref. C).
7) Keep the electric controls connection compartment clean (fig. 1, ref.15) by using compressed air or
an aspirator. Avoid taking in direct contact with water.
8) If the grass is wet or very tall, do not cut in the lowest position, but at an intermediate height.
9) Check the tension of the belts that work the deck; use the adjuster if necessary (fig. 19, ref.A).
10) Check that the blades are not worn or damaged.
11) Check the engine revs (3350 max).
12) While mowing keep the engine at maximum revs.; if the engine revs. drop, slow down for a while to
allow the engine to reach the right level again.
13) Check the blades are fitted properly.
14) Check the deck is aligned to the ground.
15) ATTENTION! Road circulation is forbidden as the machine has no type-approval.
MOWING POSITIONS
Use the electrical button on the dashboard to adjust cutting height (fig. 1, n°4).
When working on rough terrain, with bumps or humps, it is better to use the deck in the highest cutting
position to avoid impact with the blade.
Attention! During the cut the deck removal button (fig. 17, ref.D) has to be in the "floating" position (switch
indicator light off).
FX27 / Translation of the original instructions
- 7 -