Idiomas disponibles
Idiomas disponibles
10. USING THE SIGHT LIGHT
To turn on the light, press the on/off switch and make sure
the forward/reverse rotation control is on right/left position.
When you release the on/off switch, the light will be off.
LED lighting increases visibility-great for dark or enclosed
area.
LED is also a battery capacity indicator. It will flash when
power gets low.
11. BELT CLIP (SEE FIG. F)
Screw the Belt Clip on the tool with the screw provided in
the plastic bag. The belt clip can be hooked on your belt or
pocket, etc.
12. DRILLING
When drilling into a hard smooth surface, use a center
punch to mark the desired hole location. This will prevent the
drill bit from slipping off center as the hole is started. Hold
the tool firmly and place the tip of the bit at the point to be
drilled. Depress the switch trigger to start the tool. Move the
drill bit into the workpiece, applying only enough pressure to
keep the bit cutting. Do not force or apply side pressure to
elongate a hole.
If you want to activate the drill function (For drilling metal
wood or plastic), turn the torque adjustment ring on the drill
position.
If you want to activate the impact function(For masonry or
concrete), turn the torque adjustment ring on the hammer
position.
Tungsten carbide drill bits should always be used for
concrete and masonry. When drilling in metal, only use HSS
drill bits in good condition. Always use a magnetic bit holder
(not included) when using short screwdriver bits. When
screw-driving, apply a small quantity of liquid soap or similar
to the screw threads to ease insertion.
13. OVERLOAD PROTECTION
When overloaded, the motor comes to a stop. Relieve the
load on the tool immediately and release the on/off switch.
Restart the tool as normal.
14. TEMPERATURE DEPENDENT OVERLOAD
PROTECTION
When using as intended for the power tool cannot be subject
to overload. When the load is too high or the allowable
battery temperature is too hot, the electronic control
switches off the power tool until the temperature is in the
optimum temperature range again.
15. PROTECTION AGAINST DEEP
DISCHARGING
The LITHIUM-ION battery is protected against deep
EN
discharging by the "Discharging Protection System". When
the battery is empty, the tool is switched off by means of a
protective circuit: The drill will no longer rotate. Remove the
battery and recharge.
16. DISPOSAL OF AN EXHAUSTED BATTERY
PACK
To preserve natural resources, please recycle or
dispose of the battery pack properly. This battery
pack contains Lithium batteries. Consult your local
waste authority for information regarding available recycling
and/or disposal options.
Discharge your battery pack by operating your drill, then
remove the battery pack from the drill housing and cover the
battery pack connections with heavy-duty adhesive tape to
prevent short circuit and energy discharge. Do not attempt
to open or remove any of the components.
PROBLEM SOLUTION
1. WHY DOES THE DRILL NOT TURN ON
WHEN YOU PRESS THE SWITCH?
The forward/reverse rotation control, which is on top of
the trigger, is positioned in the lock function. Unlock the
forward/reverse rotation control by putting it into the
required rotation position. Push the trigger and the drill will
start to rotate.
2. THE DRILL STOPS BEFORE THE SCREW
IS COMPLETELY TIGHTENED. WHY?
Verify the torque position of the torque adjusting ring, you
can find the torque-adjusting ring between the chuck and
the drill body. Position 1 is the lowest torque (screw driving
force) and position 21 is the highest torque (screw driving
force). Position is for drill operation. Position
hammer drill operation. Regulate the torque adjusting ring to
a higher position to reach the best result.
3. I CANNOT FIT THE BATTERY INTO THE
BATTERY CHARGER. WHY?
The battery can be inserted into the charger only in one
direction. Turn the battery around until it can be inserted
into the slot.
4. REASONS FOR DIFFERENT BATTERY
PACK WORKING TIMES
Charging time problems, as above, and having not used a
battery pack for a prolonged time will reduce the battery
pack working time. This can be corrected after several
charge and discharge operations by charging & working
with your drill. Heavy working conditions such as large
is for
19
