Starting The Engine; Stopping The Engine - Craftsman CX Serie Manual Del Operador

STARTING THE ENGINE

WARNING
Always keep hands and feet clear of moving parts. Do not use a
pressurized starting fluid. Vapors are flammable.
NOTE: Allow the engine to warm up for a few minutes after starting.
The engine will not develop full power until it reaches operating
temperatures.
1. Make certain both the auger control and wheel drive control are in
the disengaged (released) position.
2. Insert key into slot. Make sure it snaps into place. Do not attempt
to turn the key.
NOTE: The engine cannot start without the key fully inserted into the
ignition switch.
Electric Starter
WARNING
The optional electric starter is equipped with a grounded three-wire
power cord and plug, and is designed to operate on 120 volt AC
household current. It must be used with a properly grounded three-
prong receptacle at all times to avoid the possibility of electric shock.
Follow all instructions carefully prior to operating the electric starter.
Determine that your home's wiring is a three-wire grounded system.
Ask a licensed electrician if you are not certain.
If you have a grounded three-prong receptacle, proceed as follows:
1. Plug the extension cord into the outlet located on the engine's
surface. Plug the other end of extension cord into a three-prong
120-volt, grounded, AC outlet in a well-ventilated area.
2. Move throttle control to FAST (rabbit)
3. Move choke to the CHOKE position
NOTE: If the engine is already warm, place choke control in the
RUN position instead of CHOKE
4. Push primer three times (3x), making sure to cover vent hole in
primer bulb when pushing. If engine is warm, push primer only
once. Always cover vent hole when pushing. Cool weather may
require priming to be repeated.
5. Push starter button to start engine. Once the engine starts, im-
mediately release starter button. Electric starter is equipped with
thermal overload protection; system will temporarily shut-down to
allow starter to cool if electric starter becomes overloaded.
CAUTION
To prolong starter life, use short starting cycles (5 seconds maximum,
then wait one minute).
6. As the engine warms, slowly rotate the choke control to the RUN
position. If the engine falters, restart engine and run with choke
at half-choke position for a short period of time, and then slowly
rotate the choke into the RUN position.
7. After engine is running, disconnect power cord from electric
starter. When disconnecting, always unplug the end at the wall
outlet before unplugging the opposite end from the engine.
OPERATION
position.
(cold engine start).
position.
17
Recoil Starter
CAUTION
Do not pull the starter handle while the engine running.
1. Move throttle control to FAST (rabbit)
2.
Move choke to the CHOKE
engine is warm, place choke in the RUN position.
3. Push primer three times, making sure to cover vent hole when
pushing. If engine is warm, push primer only once. Always cover
vent hole when pushing. Cool weather may require priming to be
repeated.
4. Pull gently on the starter handle until it begins to resist, then pull
quickly and forcefully to overcome the compression. Engine should
start. Do not release the handle and allow it to snap back. Return
rope SLOWLY to original position. If required, repeat this step.
5. As the engine warms, slowly rotate the choke control to the RUN
position. If the engine falters, restart engine and run with choke
at half-choke position for a short period of time, and then slowly
rotate the choke into the RUN position.
WARNING
To avoid unsupervised engine operation, never leave the machine
unattended with the engine running. Turn the engine off after use and
remove key.

STOPPING THE ENGINE

After you have finished snow-throwing, run engine for a few minutes
before stopping to help dry off any moisture on the engine.
1. Move throttle control to STOP
CAUTION
Do NOT move the choke control to CHOKE
the engine. Backfire or engine damage may occur.
2. Remove the key. Removing the key will reduce the possibility of
unauthorized starting of the engine while equipment is not in use.
Keep the key in a safe place. The engine cannot start without the key.
3. Wipe all snow and moisture from the area around the engine as
well as the area in and around the wheel drive control and auger
control. Also, engage and release both controls several times.
TO ENGAGE WHEEL DRIVE
1. With the throttle control in the Fast (rabbit)
speed selector lever into one of the six forward (F) positions or
two reverse (R) positions. Select a speed appropriate for the
snow conditions and a pace you're comfortable with.
NOTE: When selecting a Drive Speed, use the slower speeds
until you are comfortable and familiar with the operation of the
snow thrower.
2. Squeeze the drive control against the handle and the snow
thrower will move. Release it and drive motion will stop.
NOTE: NEVER reposition the speed selector lever (change speeds or
direction of travel) without first releasing the drive control and bringing
the snow thrower to a complete stop. Doing so will result in premature
wear to the snow thrower's drive system.
position.
position (cold engine start). If
position.
STOP
position to stop
position, move