Starting The Engine; Electric Starter; Recoil Starter; Stopping The Engine - Craftsman CX Serie Manual Del Operador

Starting The Engine

Always keep hands and feet clear of moving parts. Do not use a pressurized
starting fluid. Vapors are flammable.
NOTE: Allow the engine to warm up for a few minutes after starting. The
engine will not develop full power until it reaches operating temperatures.
1. Make certain both the auger control and wheel drive control are in the
disengaged (released) position.
2. Insert key into slot. Make sure it snaps into place. Do not attempt to turn the
key.
NOTE: The engine cannot start without the key fully inserted into the
ignition switch.

Electric Starter

The optional electric starter is equipped with a grounded power plug, and
is designed to operate on an extension cord rated for 15 amps at 125 volts,
grounded and rated for outdoor use using 120 volt AC household current. It
must be used with a properly grounded three-prong receptacle at all times
to avoid the possibility of electric shock. Follow all instructions carefully
prior to operating the electric starter.
Determine that your home's wiring is a three-wire grounded system. Ask a licensed
electrician if you are not certain.
If you have a grounded three-prong receptacle, proceed as follows:
1. Plug an extension cord into the outlet located on the engine's surface. Plug
the other end of extension cord into a three-prong 120-volt, grounded, AC
outlet in a well-ventilated area.
The extension cord can be any length, but
volts, grounded and rated for outdoor use.
2. Move throttle control to FAST (rabbit)
3. Move choke to the CHOKE position
NOTE: If the engine is already warm, place choke control in the RUN position
instead of CHOKE position.
4. Push primer three times (3x), making sure to cover vent hole in primer bulb
when pushing. If engine is warm, push primer only once. Always cover vent
hole when pushing. Cool weather may require priming to be repeated.
5. Push starter button to start engine. Once the engine starts, immediately
release starter button. Electric starter is equipped with thermal overload
protection; system will temporarily shut-down to allow starter to cool if
electric starter becomes overloaded.
To prolong starter life, use short starting cycles (5 seconds maximum, then
wait one minute).
WARNING
WARNING
CAUTION
be rated for 15 amps at 125
must
position.
(cold engine start).
CAUTION
OPERATION
6. As the engine warms, slowly rotate the choke control to the RUN position. If
the engine falters, restart engine and run with choke at half-choke position
for a short period of time, and then slowly rotate the choke into the RUN
position.
7. After engine is running, disconnect power cord from electric starter. When
disconnecting, always unplug the end at the wall outlet before unplugging
the opposite end from the engine.

Recoil Starter

Do not pull the starter handle while the engine running.
1. Move throttle control to FAST (rabbit)
2. Move choke to the CHOKE
warm, place choke in the RUN position.
3. Push primer three times, making sure to cover vent hole when pushing.
If engine is warm, push primer only once. Always cover vent hole when
pushing. Cool weather may require priming to be repeated.
4. Pull gently on the starter handle until it begins to resist, then pull quickly and
forcefully to overcome the compression. Engine should start. Do not release the
handle and allow it to snap back. Return rope SLOWLY to original position. If
required, repeat this step.
5. As the engine warms, slowly rotate the choke control to the RUN position. If
the engine falters, restart engine and run with choke at half-choke position
for a short period of time, and then slowly rotate the choke into the RUN
position.
To avoid unsupervised engine operation, never leave the machine
unattended with the engine running. Turn the engine off after use and
remove key.

Stopping The Engine

After you have finished snow-throwing, run engine for a few minutes before
stopping to help dry off any moisture on the engine.
1. Move throttle control to STOP
Do NOT move the choke control to CHOKE
engine. Backfire or engine damage may occur.
2. Remove the key. Removing the key will reduce the possibility of unauthorized
starting of the engine while equipment is not in use. Keep the key in a safe place.
The engine cannot start without the key.
3. Wipe all snow and moisture from the area around the engine as well as the
area in and around the wheel drive control and auger control. Also, engage
and release both controls several times.
16
CAUTION
position.
position (cold engine start). If engine is
WARNING
position.
STOP
CAUTION
position to stop the