Berner BACIS 14,4V LI Instrucciones De Servicio página 25

2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so may
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very "heart" of the power
tool.
Exercise due care to ensure the winding does not become
damaged and/or wet with oil or water.
4. Inspecting the carbon brushes (Fig. 12)
The motor employs carbon brushes which are consumable
parts. Since and excessively worn carbon brush can
result in motor trouble, replace the carbon brush with new
ones when it becomes worn to or near the "wear limit". In
addition, always keep carbon brushes clean and ensure
that they slide freely within the brush holders.
NOTE:
When replacing the carbon brush with a new one, be sure
to use the Berner Carbon Brush Code No. 999054.
5. Replacing carbon brushes
Take out the carbon brush by first removing the brush cap
and then hooking the protrusion of the carbon brush with
a slotted head screw driver, etc., as shown in Fig. 14.
When installing the carbon brush, choose the direction so
that the nail of the carbon brush agrees with the contact
portion outside the brush tube. Then push it in with a finger
as illustrated in Fig. 15. Lastly, install the brush cap.
CAUTION:
Be absolutely sure to insert the nail of the carbon brush
into the contact portion outside the brush tube. (You can
insert whichever one of the two nails provided.)
Caution must be exercised since any error in this operation
can result in the deformed nail of the carbon brush and
may cause motor trouble at an early stage.
6. Cleaning of the outside
When the impact driver is stained, wipe with a soft dry cloth
or a cloth moistened with soapy water. Do not use chloric
solvents, gasoline or paint thinner, as they melt plastics.
7. Storage
Store the impact driver in a place in which the temperature
is less than 40°C, and out of reach of children.
8. Service parts list
CAUTION
Repair, modification and inspection of Berner Power
Tools must be carried out by a Berner Authorized Service
Center.
This Parts List will be helpful if presented with the tool to
the Berner Authorized Service Center when requesting
repair or other maintenance.
In the operation and maintenance of power tools, the safety
regulations and standards prescribed in each country must
be observed.
MODIFICATIONS
Berner Power Tools are constantly being improved
and modified to incorporate the latest technological
advancements.
Accordingly, some parts may be changed without prior
notice.
GUARANTEE
We guarantee Berner Power Tools in accordance with
statutory/country specific regulation. This guarantee does not
cover defects or damage due to misuse, abuse, or normal wear
and tear. In case of complaint, please send the Power Tool,
undismantled, with the GUARANTEE CERTIFICATE found
at the end of this Handling instruction, to a Berner Authorized
Service Center.
NOTE:
Due to Berner's continuing program of research and
development, the specifications herein are subject to change
without prior notice.
Information concerning airborne noise and vibration
The measured values were determined according to EN60745
and declared in accordance with ISO 4871.
Measured A-weighted sound power level: 102 dB (A)
Measured A-weighted sound pressure level: 91 dB (A)
Uncertainty KpA: 3 dB (A).
Wear ear protection.
Vibration total values (triax vector sum) determined according
to EN60745.
Impact tightening of fasteners of the maximum capacity of
the tool:
a
Vibration emission value
Uncertainty K = 3.7 m/s²
WARNING
○ The vibration emission value during actual use of the power
tool can differ from the declared value depending on the
ways in which the tool is used.
○ To identify the safety measures to protect the operator
that are based on an estimation of exposure in the
actual conditions of use (taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the
trigger time).
English
h = 18.8 m/s²
24