Toshiba RAV-GM901UTP-E Manual Del Usuario página 63

 Filter sign setting
According to the installation condition, the filter sign
term (Notification of filter cleaning) can be changed.
Follow to the basic operation procedure
1 2 3 4 5 6
( → → → → → ).
3
For the CODE No. in Procedure , specify [01]
•
4
For the [SET DATA] in Procedure , select the SET
•
DATA of filter sign term from the following table.
SET DATA Filter sign term
0000 None
0001 150 H
2500 H
0002
(Factory default)
0003 5000 H
0004 10000 H
 To secure better effect of
heating
When it is difficult to obtain satisfactory heating due
to installation place of the indoor unit or structure of
the room, the detection temperature of heating can be
raised. Also use a circulator or other device to circulate
heat air near the ceiling.
Follow to the basic operation procedure
1 2 3 4 5 6
( → → → → → ).
3
For the CODE No. in Procedure , specify [06].
•
4
For the set data in Procedure , select the SET DATA
•
of shift value of detection temperature to be set up
from the following table.
SET DATA Detection temperature shift value
0000 No shift
0001 +1 °C
+2 °C
0002
(Factory default)
0003 +3 °C
0004 +4 °C
0005 +5 °C
0006 +6 °C
123-EN
 To select horizontal wind
direction
1. Push and "TEMP." buttons for at least four
seconds when the air conditioner is not working.
flashes.
Indicates CODE No. [01].
2. Select an indoor unit to be set by pushing
button (left side of the button).
Indoor unit number changes each time you push
the button.
UNIT No. UNIT No. UNIT No.
1-1 1-2 1-3
No UNIT No.
display 1-4
The fan of the selected unit runs and the louvers
start swinging.
3. Change the CODE No. to [45] with "TEMP."
buttons.
4. Select wind direction setting with "TIME"
buttons.
Wind
direction SET Wind direction setting
DATA
Smudge reducing position
0000
(Air direction to reduce ceiling
contamination) [Factory default]
Cold draft position
0002
(Air direction to control cold air fall)
5. Push button to check the setting.
The display state changes from flashing to lighting,
and the setting is fixed.
6. Push button to check the setting.
* When the cold draft position is selected, ceiling
contamination is less reduced.
 How to set up swing type
1. Push for at least four seconds when the air
conditioner is not working.
flashes.
Indicates CODE No. [F0].
flashes.
2. Select an indoor unit to be set by pushing
(left side of the button).
Each time you push the button, unit numbers
change as follows:
UNIT No. UNIT No.
1-1 1-2
No
UNIT No.
display 1-4
The fan of the selected unit runs and the louvers
start swinging.
3. Select a swing type by pushing "TIME"
buttons.
Swing SET DATA
Swing SET DATA Swing of louvers
Standard swing
0001
(Factory default)
0002 Dual swing
0003 Cycle swing
CAUTION
Do not set the swing SET DATA to "0000".
(This setting may cause a failure of the louvers.)
– 62 –
About "Dual swing"
•
"Dual" means that louvers 01 and 03 are directed
and swing in one direction and louvers 02 and 04 are
directed and swing in the opposite direction. (When
louvers 01 and 03 are directed downward, louvers 02
and 04 are directed horizontally.)
About "Cycle swing"
•
The four louvers swing independently at respective
timings.
Electrical control box
UNIT No.
1-3
Refrigerant
pipe
0 4
Drain
pipe
4. Push button.
5. Push button to complete the setting.
03
02
01
EN
124-EN