Applicable Controls - Toshiba RAV-GM901UTP-E Manual Del Usuario

8

Applicable controls

REQUIREMENT
• When you use this air conditioner for the first time,
it takes approx. 5 minutes until the remote controller
becomes available after power-on. This is normal.
<When power is turned on for the first time after
installation>
It takes approx. 5 minutes until the remote controller
becomes available.
Approx. 5 minutes
Remote
"SETTING" "SETTING"
Power on controller is
flashes goes out
available
<When power is turned on for the second (or later)
time>
It takes approx. 1 minutes until the remote controller
becomes available.
Approx. 1 minutes
Remote
"SETTING" "SETTING"
Power on controller is
flashes goes out
available
Normal settings were made when the indoor unit
•
was shipped from factory.
Change the indoor unit settings as required.
Use the wired remote controller to change the
•
settings.
The settings cannot be changed using the wireless
*
remote controller, sub remote controller, or remote-
controller-less system (for central remote controller
only). Therefore, install the wired remote controller
to change the settings.
121-EN
 Basic procedure for changing
settings
Change the settings while the air conditioner is not
working. (Stop the air conditioner before making
settings.)
CAUTION
Set only the CODE No. shown in the following table: Do
NOT set any other CODE No.
If a CODE No. not listed is set, it may not be possible
to operate the air conditioner or other trouble with the
product may result.
The displays appearing during the setting process
*
differ from the ones for previous remote controllers
(AMT31E). (There are more CODE No.)
1
3
4
6
1 5 2
1
Push and hold button and "TEMP."
button simultaneously for at least 4
seconds. After a while, the display flashes
as shown in the figure. Confirm that the
CODE No. is [01].
If the CODE No. is not [01], push button
•
to clear the display content, and repeat the
procedure from the beginning. (No operation of
the remote controller is accepted for a while
after button is pushed.)
(While air conditioners are operated under the
group control, "ALL" is displayed first. When
is pushed, the indoor unit number
displayed following "ALL" is the header unit.
(* Display content varies with the indoor unit
model.)
– 61 –
2
Each time button is pushed, indoor
unit numbers in the control group change
cyclically. Select the indoor unit to change
settings for.
The fan of the selected unit runs and the louvers
start swinging. The indoor unit for change
settings can be confirmed.
3
Specify CODE No. [ ] with "TEMP."
/ buttons.
4
Select SET DATA [ ] with "TIME"
/ buttons.
5
Push button. When the display changes
from flashing to lit, the setup is completed.
• To change settings of another indoor unit,
repeat from Procedure 2.
• To change other settings of the selected indoor
unit, repeat from Procedure 3.
Use button to clear the settings. To make
settings after button was pushed, repeat from
Procedure 2.
6
When settings have been completed, push
button to determine the settings.
When button is pushed,
then the display content disappears and the air
conditioner enters the normal stop mode.
(While is flashing, no operation of the
remote controller is accepted.)
 Installing indoor unit on high
ceiling
When an indoor unit is installed on a ceiling higher
than the standard height, make the high-ceiling setting
for fan speed adjustment.
Follow to the basic operation procedure
1 2 3 4 5 6
( → → → → → ).
For the CODE No. in Procedure 3, specify [5d].
•
Select the SET DATA for Procedure 4 from the
•
"Height list of ceiling possible to be installed" table in
this manual.
Remote controller-less setting
Change the high-ceiling setting with the DIP switch on
the receiver section P.C. board.
For details, refer to the manual of the wireless remote
controller kit. The settings can also be changed with
the switch on the indoor microcomputer P.C. board.
* Once the setting is changed, setting to 0001 or 0003
is possible, however setting to 0000 requires a
setting data change to 0000 using the wired remote
controller (separately sold) with the normal switch
setting (factory default).
flashes and
SW501-1
SW501-2
MCU(IC501)
SET DATA SW501-1
0000
OFF
(Factory default)
0001 ON
0003 OFF
To restore the factory defaults
To return the DIP switch settings to the factory defaults,
set SW501-1 and SW501-2 to OFF, connect a
separately sold wired remote controller, and then set
the data of CODE No. [5d] to "0000".
SW501-2
OFF
OFF
ON
122-EN