Makita 4331D Manual De Instrucciones página 5

ENGLISH
1 Button
2 Battery cartridge
3 Loosen
4 Hex wrench
5 Bolt
6 Jig saw blade
7 Roller
8 The end of the blade shank
should reach the bottom of the
inner slit.
9 Lever
SPECIFICATIONS
Model
Length of stroke ........................................................................... 26 mm
Max. cutting capacities
Wood ........................................................................................ 65 mm
Mild steel .................................................................................. 10 mm
Aluminum .................................................................................. 20 mm
Strokes per minute ...................................................................... 500 – 2,800
Overall length .............................................................................. 280 mm
Net weight .................................................................................... 2.6 kg
Rated voltage .............................................................................. D.C. 12 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for the sawing of wood, plastic and
metal materials.
As a result of the extensive accessory and saw blade
program, the tool can be used for many purposes and is
very well suited for curved or circular cuts.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
Explanation of general view
10 Speed adjusting dial
11 Lock-off button
12 Switch trigger
13 Base
14 Cutting line
15 Bolt
16 Cross-shaped slot
17 Edge of motor housing
18 Graduations
19 Starting hole
20 Anti-splintering device
6.
7.
8.
9.
ENC004-1
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1.
2.
3.
4.
21 Plastic base plate
22 Guide rule
23 Threaded knob
24 Circular guide
25 Pin
26 Fit into notches.
27 Plastic cover
28 Nozzle
29 Limit mark
30 Screwdriver
31 Brush holder cap
4331D
Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
Be careful not to drop or strike battery.
Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
Charge the battery cartridge with room tempera-
ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-
tery cartridge cool down before charging it.
Charge the Nickel Metal Hydride battery car-
tridge when you do not use it for more than six
months.
4333D
26 mm
65 mm
10 mm
20 mm
500 – 2,600
280 mm
2.9 kg
D.C. 14.4 V
5