Hun - Redmond SkyCooker RMC-M226S-E Manual De Instrucciones

4. When the appliance is in the standby mode, press and hold the button "+" for up to three short beeps. During the con-
nection, the display of the multicooker will show the changing symbols 0 0 and 0 0 . After the connection is established,
the appliance will give three short beeps and enter the standby mode.
IIf the Bluetooth function is disabled or the connection is not established within 30 seconds, the appliance will produce two
short beeps and enter the standby mode.
5. To disable the remote control capability in the standby mode, press and hold the button "–" until a long beep sounds. The
indicator flashes.
6. To turn off the Bluetooth function, in the standby mode of the appliance press and hold down the
indicator will go off.
To ensure a stable connection, the mobile device should be no more than 15 meters from the multicooker.
Appliance control via the wireless network. Instruction on the R4S Gateway application installation is available through
the link: www.readyforsky.com/r4sgateway
Control panel lock
For added safety, the appliance has a control panel lock function to prevent accidental button presses.
To activate the control panel lock in any mode other than setting up the program before the start and connecting to a mobile
device through the Ready for Sky application, press and hold the button
To deactivate the lock, press and hold the button , again and the symbol ] [ will appear on the display.
When the buttons are pressed while the control panel lock is on, the symbol [ ] will appear on the display.
Disabling the beeps
Press and hold the button to turn on/off the beeps in the standby mode. Its indicator will blink.
When the beeps are switched on again, the appliance will supply a short beep.
MASTERCHEF LITE function
Open even more opportunities for culinary creativity with the new MASTERCHEF LITE feature! If the MULTICOOK program
allows you to set the parameters of the program before it starts, then using the MASTERCHEF LITE function, you can change
the settings directly in the cooking process.
You can always configure the work of any program so that it corresponds to your wishes. Does the soup boil away? Does the
milk porridge "runs away"? Are the steamed vegetables cooked for too long? Change the temperature or cooking time
without interrupting the program, as if you were cooking on the stove or in the oven.
The MASTERCHEF LITE function is not available when using the EXPRESS program.
Temperature change when using the MASTERCHEF LITE function is possible in the range from 35 to 180°C in increments of 1°C. The
minimum cooking time is 1 minute, the maximum cooking time depends on the selected program, the installation step is 1 minute.
The MASTERCHEF LITE function can be especially useful if you prepare dishes according to complex recipes that require a
combination of different cooking programs (for example, when preparing cabbage rolls, beef Stroganoff, soups and pasta ac-
cording to different recipes, jam, etc.).
To change the cooking temperature
1. While the cooking program is running, press the button . The temperature indicator on the display flashes.
2. Set the desired temperature. To increase, press the button "+", to decrease — the button "—". Press and hold the desired
button to make a quick change. When the maximum (minimum) value is reached, the setting will continue from the
beginning of the range.
3. Do not press the buttons on the control panel for 5 seconds. The changes will be saved automatically.
To protect against overheating when the cooking temperature is set above 150°C, the maximum time of the program is lim-
ited to 2 hours.
Changing the cooking time
1. While the cooking program is running, press the button
2. Set the desired cooking time. To increase the hour value, press the button "+", to decrease — the button "—".
button, the button
, the symbol [ ] will appear on the display.
. The hour value indicator on the time display will blink.
3. Press the button again and set the minutes using the buttons "+" and "—". Changes in the values of hours and minutes
occur independently of each other. When the maximum value is reached, the setting will continue from the beginning
of the range. To quickly change the value, press and hold the desired button.
4. Do not press the buttons on the control panel for 5 seconds. The changes will be saved automatically.
If you set the cooking time to 00:00, the program will stop.
Time Delay function
This function allows you to set the time after which the selected cooking program will start, ranging from 1 minute to 24 hours
in 1 minute increments.
1. Press the button to select the desired cooking program.
2. Press the button . The Time Delay indicator (on the display) will blink.
3. Press the button "+" or "–" to change the time value. When you press the button "+" зthe time value will increase, when
you press the button "–", it will decrease. To quickly change the value, press and hold the desired button. When the
maximum value is reached, the time setting will continue from the beginning of the range.
4. Press the button . The countdown to the start of the cooking program will begin.
5. To cancel the settings, press the button , after which you will need to enter the entire cooking program again.
It is not recommended to use a delay start if the recipe contains perishable products (eggs, fresh milk, meat, cheese, etc.).
In the FRY and EXPRESS programs the Time Delay function is not available.
When setting the time in the Time Delay function, it should be considered that the countdown in the STEAM, FRY, RICE/GRAIN
and SOUP programs begins only after the device reaches the operating parameters.
Keep Warm function for ready meals (automatic heating)
It turns on automatically when the cooking program is completed and can maintain the temperature of the finished dish in
the range of 70-75°C for 12 hours. The display shows the direct time of operation in this mode. If necessary, automatic
heating can be turned off by pressing the button (the button indicator will turn off).
The automatic heating function is not available when using the YOGURT/DOUGH, EXPRESS programs.
Preliminary disabling the Keep Warm (automatic heating)
REDMOND SkyCooker RMC-M226S-E multicooker provides the ability to disable the automatic heating function (Keep Warm)
in advance after starting the main cooking program. To do this, after starting the program, press the button , until the in-
dicator of the button turns off. To turn on the automatic heating again, press the button
button will come on.
For your convenience, in case of cooking at temperatures up to 80°C, the automatic heating function will be disabled by default.
Dish heating function
The multicooker can be used to heat cold dishes. For this:
1. Put the food into the bowl, place it in the body of the appliance. Make sure it is in close contact with the heating element.
2. Close the lid until it clicks, connect the multicooker to the mains.
3. Press the button . The corresponding indicator on the display will come on and the heating will start. The timer will
display a direct countdown of the appliance in this mode. The dish will be heated to 70-75°C. This temperature can be
maintained for 12 hours.
4. If necessary, the heating can be turned off by pressing the button
go off.
Despite the fact that the multicooker can keep the product in a heated state up to 12 hours, it is not recommended to leave
the dish heated for more than two or three hours, as sometimes this can lead to a change in its taste.
General procedure when using the automatic programmes
IMPORTANT! If you use the appliance to boil water (for example, when cooking food), do NOT set the cooking temperature
above 100°C. This may cause the appliance to overheat and break down. For the same reason, do not use the BAKE, FRY programs
for boiling water.
SkyCooker RMC-M226S-E GBR
FRA
DEU
ITA
ESP
PRT
DNK
NOR
SWE
FIN
LTU
LVA
EST
ROU

HUN

HRV
SVK
еagain, the indicator of the
SVN
CZE
POL
SRB
GRE
. The indicators on the display and the button will
BGR
RUS
UKR
7