Black and Decker GL280 Traducción De Las Instrucciones Originales página 9

Remove the empty spool (23) from the spool cover.
u
Remove any dirt and grass from the spool cover and
u
housing.
Take the new spool and push it onto the boss in the spool
u
cover. Rotate the spool slightly until it is seated.
Unclip the end of one of the cutting lines and feed the line
u
into one of the eyelets (24). The line should protrude
approximately 9 cm from the spool cover.
Unclip the end of the other cutting line and feed the line
u
into the other eyelet. The line should protrude
approximately 9 cm from the spool cover.
Align the tabs (21) on the spool cover with the cut-outs (25)
u
in the housing.
Push the cover onto the housing until it snaps securely
u
into place.
Warning! If the cutting lines protrude beyond the trimming
blade (10), cut them off so that they just reach the blade.
Winding a new cutting line onto an empty spool
(fig. K - O)
You may wind new cutting line onto an empty spool.
Spool with single cutting line (fig. K & L)
Replacement packs of cutting line are available from your
Black & Decker dealer (cat. no. A6170 (25 m) & A6171 (40 m)).
Remove the empty spool from the tool as described above.
u
Remove any remaining cutting line from the spool.
u
Feed 2 cm of cutting line into one of the holes (26) in the
u
spool as shown.
Bend the cutting line and anchor it in the L-shaped slot (27).
u
Wind the cutting line onto the spool in the direction of the
u
arrow (28). Make sure to wind the line on neatly and in
layers. Do not criss-cross.
When the wound cutting line reaches the recesses (29),
u
cut the line. Let the line protrude approximately 9 cm from
the spool and hold a finger on the line to keep it in place.
Proceed as described above to fit the spool on the tool.
u
Warning! Only use the appropriate type of Black & Decker
cutting line.
Spool with twin cutting line (fig. M - O)
Replacement packs of cutting line are available from your
Black & Decker dealer (cat. no. A6440).
Remove the empty spool from the tool as described above.
u
Remove any remaining cutting line from the spool.
u
First wind new line onto the uppermost part of the spool:
u
- Feed 2 cm of cutting line into one of the slots (30) in the
upper section of the spool as shown.
- Wind the cutting line onto the spool in the direction of
the arrow (31). Make sure to wind the line on neatly
and in layers. Do not criss-cross.
- When the wound cutting line reaches the recesses (32),
cut the line.
- Temporarily park the line in the slots (33) on one side of
the spool as shown.
Repeat the above procedure for the second cutting line on
u
the lower section of the spool. Park the line in the unused
slots (33).
Proceed as described above to fit the spool on the tool.
u
Do not forget to release the cutting line from the parking
slots (33).
Warning! Only use the appropriate type of Black & Decker
cutting line. Ensure that cutting line is present in both sections
of the spool.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new plug.
u
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
Troubleshooting
If your tool seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local Black & Decker repair agent.
Warning! Before proceeding, unplug the tool.
Appliance runs slowly
Check that the spool housing can rotate freely. Carefully
u
clean it if necessary.
Check that the cutting line does not protrude more than
u
11 cm from the spool housing. If it does, cut it off so that it
just reaches the line trimming blade.
Automatic line feed does not work
Keep the tabs depressed and remove the spool cover
u
from the housing.
Pull the cutting line until it protrudes 11 cm from the
u
housing. If insufficient cutting line is left on the spool,
install a new spool of cutting line as instructed above.
Align the tabs on the spool cover with the cut outs in the
u
housing.
Push the cover onto the housing until it snaps securely
u
into place.
If the cutting line protrudes beyond the trimming blade,
u
cut it off so that it just reaches the blade.
If the automatic line feed still does not work or the spool is
jammed, try the following suggestions:
Carefully clean the spool cover and housing.
u
Remove the spool and check if the lever can move freely.
u
Remove the spool and unwind the cutting line, then wind it
u
ENGLISH
9