Driving The Machine; Work Method; Preparation And Warnings; Battery Charge Level Controls - Lavorwash FREE EVO 50E Manual De Instrucciones

6.13 DRIVING THE MACHINE

Model AC 230V
- Connect the power cable of the machine ( Photo
B - 1) to the power mains using a patch cord.
- Switch ON the general ON-OFF switch ( Photo A -
1).
- Switch ON the brush motor switch ( Photo A - 2).
!
( ) The brush will start the rotation only
when the machine operator will operate the
brush operation lever ( Photo B - 4).
- Switch ON the suction motor switch ( Photo A - 3).
- Lower the squeegee unit by using the lift/lower
lever ( Photo B - 3)
- Lower the brush plate unit by using the lift/lower
lever ( Photo B - 2)
- Wash the floor moving forward slowly, pulling the
brush operation lever ( Photo B - 4); releasing the
lever the brush rotation will stop after few seconds.
To adjust the outflow of the cleaning solution
it is necessary to act on cap of the solution
water filter (Photo Q - 1); screwing the tran-
sparent cap increases the amount of flow,
while unscrewing the cap reduces the flow.
!
( ) Remember to lift the squeegee before driving
reverse to avoid damaging it.
Model DC 24V
- Verify that the battery connector placed in the
back of the machine ( Photo D - 7) is connected.
- Put the ignition key ( Photo D - 1) in and turn ON
the machine.
- In the control panel, check the battery charge sta-
tus ( Photo C - 3 )
- Switch ON the brush motor switch ( Photo C - 1).
!
( ) The brush will start the rotation only
when the machine operator will operate the
brush operation lever ( Photo D - 2).
- Switch ON the suction motor switch ( Photo C - 2).
- Lower the squeegee unit by using the lift/lower
lever ( Photo D - 4)
- Lower the brush plate unit by using the lift/lower
lever ( Photo D - 3)
- Wash the floor moving forward slowly, pulling the
brush operation lever ( Photo D - 2); releasing the
lever the brush rotation will stop after few seconds.
To adjust the outflow of the cleaning solution
it is necessary to act on cap of the solution
water filter (Photo Q - 1); screwing the tran-
sparent cap increases the amount of flow,
while unscrewing the cap reduces the flow.
!
( ) Remember to lift the squeegee before driving
reverse to avoid damaging it.
Model DC 24V with traction
- Verify that the battery connector placed in the
back of the machine ( Photo F - 8) is connected.
- Put the ignition key ( Photo F - 1) in and turn ON
the machine.
- In the control panel, check the battery charge sta-
tus ( Photo E - 1 ) and, if sufficient, select the run-
ning speed wished ( Photo E - 3, E - 4 ).
- Switch ON the brush motor switch ( Photo E - 5).
!
( ) The brush will start the rotation only
when the machine operator will operate the
brush operation lever ( Photo F - 2).
- Switch ON the suction motor switch ( Photo E - 6).
- Lower the squeegee unit by using the lift/lower
lever ( Photo F - 4)
- Lower the brush plate unit by using the lift/lower
lever ( Photo F - 3)
- Wash the floor moving forward by pulling the trac-
tion lever ( Photo F - 2) up or push the traction
lever down to reverse traction; releasing the lever
the traction will stop immediately and brush rota-
tion will stop after few seconds.
To adjust the outflow of the cleaning solution
it is necessary to act on cap of the solution
water filter (Photo Q - 1); screwing the tran-
sparent cap increases the amount of flow,
while unscrewing the cap reduces the flow.
!
( ) Remember to lift the squeegee before driving
reverse to avoid damaging it.

6.14 WORK METHOD

6.14.1 PREPARATION AND WARNINGS

Remove any loose solid residue from the surface to
be treated (using suitable tools, such as vacuum
cleaners, sweepers, etc.). It this is not done, the
solid dirt might prevent the squeegee from operat-
ing correctly, reducing drying efficiency.
Only trained personnel can drive this machine.

6.14.2 BATTERY CHARGE LEVEL CONTROLS

The sequence of lights of the battery charge control
( Photo C - 3, E - 1 ) progressively turns off until the
battery is discharged . When the red light turns on
( Photo C - 3C, E - 1C ), turn off the brush motor,
close the detergent solution outlet, finish drying the
small residual moisture and go to the battery charg-
ing area to charge the battery.
!
( ) The batteries may be irreparably dam-
aged if the residual charge level drops too
low (see the battery operating manual). Do
not force the battery discharge beyond the
safety limits, turning the key off and on or in
any other manner.
6.14.3 DIRECT
SLIGHTLY DIRTY SURFACES
Scrubbing and drying in a single pass.
Prepare the machine as previously described and
use it as described in paragraph 6.13.
☞
( ) Never use the machine without the detergent
solution: the floor might be damaged.
39
SCRUBBING OR FOR