Protecting The Environment; Technical Data - Black+Decker GL933 Traducción De Las Instrucciones Originales

ENGLISH
Note: Take care not to allow the the line on the spool to
unravel. Hold it firmly with one hand at all times.
Take the new spool and push it onto the boss in the spool
u
cover. Rotate the spool slightly until it is seated.
Align the tabs (17) on the spool cover with the cut outs
u
(24) in the housing (12).
Push the cover onto the housing until it snaps securely
u
into place.
Warning! If the cutting lines protrude beyond the trimming
blade (11), cut it off so that it just reaches the blade.
Fitting a new piece of heavy duty cutting line
(fig. O & P)
Replacement packs of 10 heavy duty cutting lines are
available from your BLACK+DECKER dealer (cat. no. A6489).
To fit a new piece of cutting line, proceed as follows:.
Unplug the tool.
u
Keep the tabs (17) depressed and remove the HDL cap
u
(9) from the housing (12).
Remove any dirt and grass from the HDL cap (9) and
u
housing.
Remove the used piece of line from the HDL cap (9).
u
Thread a new piece of line (20) through the eyelets (27) in
u
either side of the HDL cap.
Put the central ferrule (28) in the indicated position
u
(Fig. P).
Re-fit the HDL cap.
u
Warning! Only use the appropriate type of BLACK+DECKER
cutting line.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
Troubleshooting
If your tool seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local BLACK+DECKER repair agent.
Warning! Before proceeding, unplug the tool.
Tool runs slowly
Check that the spool housing can rotate freely. Carefully
u
clean it if necessary.
Check that the cutting line does not protrude more than
u
11 cm from the spool housing. If it does, cut it off so that it
just reaches the line trimming blade.
10
(Original instructions)
Automatic line feed does not work
Keep the tabs depressed and remove the spool cover
u
from the housing.
Pull the cutting line until it protrudes 11 cm from the
u
housing. If insufficient cutting line is left on the spool,
install a new spool of cutting line as instructed above.
Align the tabs on the spool cover with the cut outs in the
u
housing.
Push the cover onto the housing until it snaps securely
u
into place.
If the cutting line protrudes beyond the trimming blade, cut
u
it off so that it just reaches the blade.
If the automatic line feed still does not work or the spool is
jammed, try the following suggestions:
Carefully clean the spool cover and housing.
u
Remove the spool and check if the lever can move freely.
u
Remove the spool and unwind the cutting line, then wind it
u
on neatly again as described above. Replace the spool as
instructed.

Protecting the environment

Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com

Technical data

Voltage
Power input
No-load speed
Weight
Level of sound pressure:
Sound pressure (L ) 80 dB(A), uncertainty (K) 0.55 dB(A)
pA
Sound power (L ) 94 dB(A), uncertainty (K) 0.55 dB(A)
WA
Vibration total values (triax vector sum) according to EN 50636-2-91:2014:
2
Vibration emission value (a ) 6.0 m/s , uncertainty (K) 1.5 m/s
h
GL933
(Type 1)
230
V
AC
W 900
-1
7000
min
kg 3.2
2