Protecting The Environment; Troubleshooting; Technical Data - Black+Decker BDST182ST1 Manual De Instrucciones

ENGLISH
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your tool/appliance
u
and charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Regularly clean the cutting line and spool using a soft
u
brush or dry cloth.
Regularly use a blunt scraper to remove grass and dirt
u
from the underneath of the guard.

Troubleshooting

Problem
Appliance runs slowly.
Automatic line feed does not
feed line.
Overfeeding
Line unravels when cap or
spool is removed
14
(Original instructions)
Solution
Remove battery from trimmer.
Check that the spool housing can rotate
freely. Carefully clean it if necessary.
Check that the cutting line does not
protrude more than approximately
122 mm from the spool. If it does, cut
it off so that it just reaches the line
trimming blade
More line is fed when the line shortens
to approximately 76 mm. To determine if
the line is not feeding, let line wear past
this point.
Keep the tabs depressed and remove the
spoolcap with the spool from the spool
housing in the trimmer head.
Ensure that the line is not crisscrossed
on the spool as detailed in (Fig. U). If
it is unwind the cutting line and rewind
it neatly.
Inspect tracks at the bottom of spool for
damage. If damaged, replace spool.
Pull the cutting line until it protrudes
approximately 122 mm from the spool. If
insufficient cutting line is left on the spool,
install a new spool of cutting line.
Align the tabs on the spool cap with the
cut outs in the housing.
Push the spool cap onto the housing until
it snaps securely into place.
If the cutting line protrudes beyond the
trimming blade, cut it off so that it just
reaches the blade. If the automatic line
feed still does not work or the spool is
jammed, try the following suggestions:
Carefully clean the spool and housing.
Make sure you are using correct line
size and diameter (2.00 mm) - smaller
and larger line sizes will affect the
functionality of the auto feed system.
Remove the spool and check if the lever
in the spool housing can move freely.
Remove the spool and unwind the cutting
line, then wind it on neatly again. Replace
the spool into the housing.
Ensure you are cutting with the tip of
the line 177 mm from the spool. Use the
edge guide if needed to ensure proper
space is maintained.
Ensure you are not exceeding a 10º
angle as shown in (Fig. J1). Avoid contact
of the line with hard surfaces such as
brick, concrete, wood etc. This will
prevent excessive wear and/or overfeed
of line. Cut with the tip of the line
Make sure to park the lines in holding
slots (Figure P) before removing.

Protecting the environment

Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according
to local provisions. Further information is available at
www.2helpU.com

Technical data

STC1820EPC
H1
Voltage V 18
DC
No-Load Speed min 5500 - 7400
-1
Weight kg 2.1
Battery BL2018
Voltage V 18
DC
Capacity Ah
Type Li-Ion
Charger 905902**
(Type 1)
Input voltage V 100 - 240
DC
Output voltage Ah 8 - 20
Current
mA 400
BDST182ST1 H1
Voltage V
DC
Blade strokes
min
-1
(no load)
Weight kg
Battery
Voltage V
DC
Capacity Ah
Type
Charger
Input voltage V
AC
Output voltage V
DC
Current mA
STC1820EPCF STC1840EPC
H1 H1
18 18
5500 - 7400 5500 - 7200
2.1 2.1
BL2018 BL4018
18 18
2 2
Li-Ion Li-Ion
905902** 906068**
(Type 1)
100 - 240 230
8 - 20 18
400 2000
STC1820PST H1
18 18
5500 - 7400 5500 - 7400
2.1 2.1
BL2018ST BL2018ST
18 18
2 2
Li-Ion Li-Ion
906349** 905902** (Type 1)
200-240 100 - 240
8-20 8 - 20
1000 400
4