Care And Maintenance - Zeiss VICTORY HT Modo De Empleo

b) After shooting, pull the knob (6 bzw. 7) upward out of the catch and set the zero mark of the
sub-ring (8) on the index mark (9). Press the knob (6 or 7) downward into the catch.
The index is used to again find the original location when adjusting the reticle later (for other
distances or other loads).
c) Do not forget: Screw the protective lens cap (1 or 2) back on.
note: When the ZeISS VICTORY HT series riflescope is delivered, the reticle is set to the middle of
the adjustment range and the zero mark of the adjusting ring (8) to the indexmark (9). From this
initial setting, an upward, downward, right or left adjustment is possible for more than half of the
adjustment ranges given in the following table.
The elevation shot correction for the riflescope with bDc+ rapid reticle is described in detail in the
enclosed instructions for use for the rapid reticle.
The ZeISS VICTORY HT riflescopes are designed so that when the reticle is adjusted, even a
corresponding movement of the reticle to the centre of the image is not noticeable. The reticle
always remains in the centre of the image during all adjustments.
seal integrity
The riflescope is waterproof, pressure tested to ISO 9022-80 and filled with nitrogen. The integrity
of the seal is also guaranteed if the protective lens caps (1 or 2) of the reticle adjustment are not
screwed on. However, always ensure a good seat of these protective lens caps (1 or. 2) and the
sealing ring under them.
reticle
Your riflescope is equipped with the reticle of your choice. For the ZeISS VICTORY HT models the
reticle is in the second level. The reticle is not magnified during magnification change, but rather
it always remains the same. Thus for these riflescopes the dimension of change of the reticle is
dependent on the magnification.
For an overview of the reticles and dimensions of coverage currently available, visit
www.zeiss.de/subtensions or contact us at:
Carl Zeiss
Sports Optics GmbH
Carl Zeiss Group
Gloelstraße 3 – 5
D-35576 Wetzlar
reticle retrofitting
The ZeISS VICTORY HT riflescope can of course also be retrofitted with other available reticles. For
reticle retrofitting, please send the riflescope to our customer service.
12

care and maintenance

Your riflescope has ZeISS LotuTec coating. The effective protective coating for the lens surfaces
®
noticeably reduces contamination of the lenses through an especially smooth surface and the
resulting water-beading effect. All types of contamination stick less and can be quickly and easily
removed without smearing. LotuTec ® coating is durable and abrasion-resistant.
Your ZeISS riflescope requires no special maintenance. Do not wipe coarse particles (e. g. sand) from
the lenses. Blow them off, or use a soft brush! Over time, fingerprints can corrode the lens surface.
Breathing on the lens and polishing with a clean optical cleansing cloth/tissue is the easiest method
of cleaning the lens surface.
To avoid a possible fungal coating which is common in the tropics, store the optics in a dry place
and always ensure good aeration of the lens surface.
replacement parts for Zeiss VicTOrY hT
If you need any replacement parts for your riflescope, e.g. protective lens caps, please contact your
local dealer, your country's distributor or our customer service team.
Our customer service team is available from Monday to Friday from 8:00 am until 6:00 pm (CeT)
should you have any questions.
Tel.: +49 (0) 64 41-4 67 61
Fax: +49 (0) 64 41-4 83 69
accessories for Zeiss VicTOrY hT
Rubber sunshade
Bullet Drop Compensator (BDC) for elevation and windage, for new orders
* Accessory not included in the delivery program!
52 83 75 - 0000
13