Transportation And Storage; Residual Risks - Ryobi RCS1935B Traducción De Las Instrucciones Originales

back if the wood holding it is cut or removed.
On a fallen tree, a rooted stump has a high potential of
springing back to the upright position during the bucking
cut to separate the log from the stump. Watch out for
springpoles—they are dangerous. Do not attempt to cut
bent branches or stumps which are under tension unless
you are professionally trained and competent to do so.
WARNING
Springpoles are dangerous and could strike the operator,
causing the operator to lose control of the chainsaw.
This could result in severe or fatal injury to the operator.
This should be done by trained users.

TRANSPORTATION AND STORAGE

See page 281 - 284.
■ Stop the product and disconnect it from the power
supply. Allow the product to cool down before storing
or transporting.
■ Clean all foreign material from the product. Store it in a
cool, dry, and well-ventilated place that is inaccessible
to children. Keep away from corrosive agents such
as garden chemicals and de-icing salts. Do not store
outdoors.
■ Fit the guide bar cover before storing the product or
during transportation.
■ For transportation, secure
movement or falling to prevent injury to persons or
damage to the product.
MAINTENANCE
Always keep the product in good working condition.
WARNING
Use only original manufacturer's replacement parts,
accessories, and attachments. Failure to do so can
cause possible injury, poor performance, and may void
your warranty.
WARNING
Servicing requires extreme care and knowledge
and should be performed only by a qualifi ed service
technician. Have the product serviced by an authorised
service centre only. When servicing, use only original
replacement parts.
WARNING
Disconnect the product from the power supply before
adjustment, maintenance, or cleaning. Failure to do so
could result in serious personal injury.
■ You may only make adjustments or repairs described
in this manual. For other repairs, have the product
serviced by an authorised service centre only.
■
Consequences of improper maintenance, removal, or
6 | English
■
■
■
■

RESIDUAL RISKS

Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise during use, and
the operator should pay special attention to avoid the
following:
■
the product against
■
■
■
■
■
■
■
RISK REDUCTION
It has been reported that vibrations from hand-held tools
may contribute to a condition called Raynaud's Syndrome
in certain individuals. Symptoms may include tingling,
numbness and blanching of the fi ngers, usually apparent
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking and work practices
are all thought to contribute to the development of these
symptoms. There are measures that can be taken by the
operator to possibly reduce the effects of vibration:
■
■
■
modification of safety features like the chain brake,
hand guard (front and back), spiked bumper, chain
catcher, guide bar, low-kickback saw chain
cause the safety features to not function correctly, thus
increasing the potential for serious injury. Keep the
product professionally maintained and safe.
Sharpening the chain safely is a skilled task. Therefore,
the manufacturer strongly recommends that a worn or
dull chain is replaced with a new one, available at your
authorised service centre. The part number is available
in the product specification table in this manual.
Follow instructions for lubricating and chain tension
checking and adjustment.
After each use, clean the product with a soft dry cloth.
Check all nuts, bolts, and screws at frequent intervals
for security to ensure the product is in safe working
condition. Any part that is damaged should be properly
repaired or replaced by an authorised service centre.
Injury caused by vibration
– Always use the right tool for the job. Use designated
handles. Restrict working time and exposure.
Exposure to noise can cause hearing injury.
– Wear hearing protection and limit exposure.
Contact with exposed saw teeth of the chain (cutting
hazards).
Unforeseen, abrupt movement or kickback of the guide
bar (cutting hazards).
Parts ejected from the saw chain (cutting/injection
hazards).
Thrown out pieces of the work piece (wood chips,
splinters).
Inhalation of saw dust and particles.
Skin contact with oil.
Keep your body warm in cold weather. When operating
the unit wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud's Syndrome.
After each period of operation, exercise to increase
blood circulation.
Take frequent work breaks. Limit the amount of
may