Additional Safety Information - Porter Cable PCE980 Manual De Instrucciones

Ocultar thumbs

Contenido

Tabla de contenido

Idiomas disponibles

3-conductor cord and 3-prong grounding type plug to fit

the proper grounding type receptacle. The green (or green

and yellow) conductor in the cord is the grounding wire.

Never connect the green (or green and yellow) wire to a live

terminal. If your unit is intended for use on less than 150 V,

it has a plug that looks like that shown in sketch A. If it is for

use on 150 to 250 V, it has a plug that looks like that shown

in sketch D. An adapter, sketches B and C, is available for

connecting sketch A type plugs to 2-prong receptacles. The

green-colored rigid ear, lug, or the like, extending from the

adapter must be connected to a permanent ground, such as

a properly grounded outlet box. No adapter is available for a

plug as shown in sketch D. ADAPTER SHOWN IN SKETCHES B

and C ARE NOT FOR USE IN CANADA.

Fig. B

GROUNDED

OUTLET

BOX

GROUNDING PIN

GROUNDING

MEANS

ADAPTER

GROUNDING PIN

WARNING: To reduce the risk of electrocution, keep all

connections dry and off the ground. Do not touch the

plug with wet hands.

WARNING: The saw must be plugged into a GFCI

protected receptacle.

WARNING: Never use saw with salt water or a

conductive fluid.

Additional Safety Rules for Wet Tile Saw

CAUTION: Wear appropriate hearing protection

during use. Under some conditions and duration

of use, noise from this product may contribute to

hearing loss.

CAUTION: Do not connect unit to electrical

power source until complete instructions are read

and understood.

•

Use safety equipment. Always wear eye protection.

Dust mask, non-skid safety shoes, hard hat, or hearing

protection must be used for appropriate conditions.

•

Keep hands out of path of saw blade. NEVER CUT A

PIECE WHERE HAND WOULD BE 3" (76 mm) OR LESS

FROM BLADE.

•

Do not perform any operation freehand, that is without

holding the workpiece firmly against the fence or

edge guide.

•

Never reach in back of the blade.

•

DON'T - Cut dry. If blade is not cooled with water, serious

damage will occur. Dry cutting will increase exposure to

harmful airborne dust.

•

Turn off the tool and wait for blade to stop before moving

the workpiece or changing settings.

•

To reduce risk of injury, return the cart to the full rear

position after each cut.

•

DO - Make certain the blade rotates in the correct direction

as indicated by the arrow on the blade.

•

DO - Always use the splash hood.

•

DO - Be sure all clamp handles and knobs are tight before

starting any operation.

•

DO - Be sure all blade and clamp washers are clean and

recessed sides of collars are against blade. Tighten arbor

nut securely.

•

DO - Keep the blade properly aligned.

•

DO - Keep the motor air slots free of chips and dirt.

•

DO - Always empty water from the reservoir before

transporting. Water can splash into electrical components.

•

DO - Keep hands out of the path of the saw blade.

•

DON'T - Attempt to operate on anything but designated

voltage. Incorrect voltage may result in shock, fire, or

unpredictable operation.

•

DON'T - Use blades larger or smaller than those which

are recommended.

•

DON'T - Force cutting action. Allow motor to reach full

speed before cutting. Stalling or partial stalling of motor

can cause major damage.

•

DON'T - Use metal cutting abrasive wheels. The excessive heat

and abrasive particles generated by them will damage the saw.

•

DO - Use continuous rim wheels only, no serrated edges or

toothed blades.

•

DON'T - Allow anyone to stand behind saw.

•

DON'T - Place either hand in the blade area when the saw is

connected to the power source.

•

DON'T - Use blades rated less than 5000 R.P.M.

•

DON'T - Place hands closer than 3" (76 mm) from the

saw blade.

•

DON'T - Reach behind or underneath the saw unless it is

turned off and unplugged.

•

DON'T - Move either hand from saw or workpiece until the

blade has stopped.