Nice MORX Instrucciones Y Advertencias De Instalación Y Uso página 16

after the first one, by repeating step 02 for each of them within 10 seconds after
the previous card was held up to the reader.
03. To terminate the procedure, swipe the SINGLE-MASTER over the reader 1 time,
or wait for the 10 second period since the last card to time out.
If you wish, you can save more cards to the reader at any later time by repeating the
procedure.
7.B.6
Professional
To program a card for activating output-2 only (using
the SINGLE-MASTER)
01. Swipe the SINGLE-MASTER over the reader 1 time.
02. Swipe the new card over the reader 2 times. Note – You can program more
cards after the first one, by repeating step 02 for each of them within 10 seconds
after the previous card was held up to the reader.
03. To terminate the procedure, swipe the SINGLE-MASTER over the reader 1 time,
or wait for the 10 second period since the last card to time out.
If you wish, you can save more cards to the reader at any later time by repeating the
procedure.
7.B.7 Professional
To program a card for activating both output-1 and
output-2 (using the SINGLE-MASTER)
01. Swipe the SINGLE-MASTER over the reader 1 time.
02. Swipe the new card over the reader 3 times. Note – You can program more
cards after the first one, by repeating step 02 for each of them within 10 seconds
after the previous card was held up to the reader.
03. To terminate the procedure, swipe the SINGLE-MASTER over the reader 1 time,
or wait for the 10 second period since the last card to time out.
If you wish, you can save more cards to the reader at any later time by repeating the
procedure.
7.B.8 Professional
To cancel a saved card (with a MASTER...)
01. Swipe the MASTER(*) over the reader 2 times.
02. Swipe the card to be cancelled over the reader 1 time. Note – You can cancel
more cards after the first one, by repeating step 02 for each of them within 10
15 – English
seconds after the previous card was held up to the reader.
03. To terminate the procedure, swipe the MASTER (the same one you used in
step 01) over the reader 1 time, or wait for the 10 second period since the last
card to time out.
If you wish, you can cancel more cards from the reader at any later time by repeating
the procedure.
(*) – You must use MASTER-1, MASTER-2 of the SINGLE-MASTER, depending on
the output (1, 2, or both) to which the card in question is mapped.
7.B.9 Professional
To count the saved cards (with a MASTER...)
01. Swipe the MASTER(*) over the reader 3 times. It will beep a number of times; the
beeps have the following meanings:
• 3 beeps = 1 hundred (e.g.: 2 sets of 3 beeps = 200 cards).
• 2 beeps = 1 ten (e.g.: 3 sets of 2 beeps = 30 cards).
• 1 beep = 1 unit (e.g.: 5 sets of 1 beep = 5 cards).
• 10 sets of single beeps = zero.
The beeps are emitted in the following order: hundreds, tens, units.
(*) – You must use MASTER-1, MASTER-2 of the SINGLE-MASTER, depending on
the output (1, 2, or both) to which the card in question is mapped. Using the SINGLE-
MASTER counts all cards mapped to both outputs.
7.B.10 Professional
To limit a card (with a MASTER...) to a set number
of uses
Each card has a counter which decrements automatically every time the combination
is used; the card is deactivated when the counter reaches zero. The factory setting is
unlimited activations. This procedure allows you to set a limit to the number of times
a card can be used. The maximum value is 999; higher values remove any limit to the
number of times the card can be used.
01. Swipe the MASTER(*) over the reader 4 times. After 2 seconds, the reader beeps
3 times and enables the hundreds.
02. Now swipe the card in question one time for each hundred times you want the
card to be used (10 swipes = unlimited use).
03. After 2 seconds, the reader beeps 2 times and enables the tens.
04. Now swipe the card in question one time for each ten times you want the card
to be used.