Squeegee "V" Type (Optional); Squeegee "V" Type (Optional): Rear Rubber Replacement; Squeegee Hose Cleaning; Cleaning Of The Solution Tank - Floorpul amber 66 24v Manual De Uso Y Mantenimiento

GB
To reassemble the squeegee repeat reverse the oper-
ations above mentioned, inserting the rubber on the
guides and blocking it with the rubber holder blade.

SQUEEGEE "V" TYPE (OPTIONAL)

Alternatively to the standard squeegee, a "V"-shaped
squeegee is available, especially indicated for floors
with large joints.
This squeegee is interchangeable with the standard
one, same assembly on the machine, same adjust-
ment in height, pressure and inclination.
Different though are the methods in assembly and
disassembly of the squeegee rubbers.
SQUEEGEE "V" TYPE (OPTIONAL): REAR RUBBER
REPLACEMENT
Check the squeegee rubber wear and eventually turn
or replace it.
For the replacement it is necessary to:
1. Lift the squeegee through the lever (17).
2. Unscrew the tie rods (1) on the terminals (2) of
the rubber holder blade and disengage the terminals.
3. Unscrew the wing nuts (3) and take off the rub-
ber holder blade (4).
4. Turn the rubber (5) to a new side or replace it.
To reassemble the squeegee repeat reverse the oper-
ations above mentioned, inserting first the rubber (5)
into its guides, then positioning the rubber holder
blade and finally screwing down all wing nuts and
the tie rods of the two terminals.

SQUEEGEE HOSE CLEANING

Weekly or in case of insufficient suction, it is neces-
sary to check that the squeegee hose is not obstruct-
ed. Eventually, to clean it, proceed as follows:
1. Take off the hose (1) from the squeegee coupling.
2. Wash the inside of the hose with a water jet.
To reassemble the hose repeat reverse the operations
above-mentioned.
ATTENTION:
Do not wash the hose that goes from the suction
motor to the suction cover.

CLEANING OF THE SOLUTION TANK

1. Bring the machine to an appropriate place for
the detergent solution draining.
2. Unscrew the solution tank cap.
3. Unscrew the cap of the exhaust filter (1) so that
the detergent solution flows out into appropriate
containers. Pay attention not to lose the gasket of
the cap.
4. Rinse with a water jet the solution tank.
5. Reassemble all parts.
27
ATTENTION:
This operation must be carried out using gloves to
protect from contact with dangerous solutions.

CLEANING OF THE SOLUTION FILTER

1. Empty the detergent solution tank as indicated in
paragraph "CLEANING OF THE SOLUTION TANK".
2. Unscrew the cap of the exhaust filter (1).
3. Rinse the filter placed inside the cap, paying at-
tention not to lose the gasket of the cap.
4. Rinse the hose pouring some water into the solu-
tion tank.
5. Reassemble all parts.
ATTENTION:
This operation must be carried out using gloves to
protect from contact with dangerous solutions.

TWO-MONTHLY MAINTENANCE

FRONT SQUEEGEE RUBBER CHECK

Check the wear of the squeegee rubber and eventu-
ally replace it.
For the replacement it is necessary to:
1. Release the squeegee from the support as indi-
cated in paragraph "SQUEEGEE CLEANING".
2. Unscrew the wing nuts in the front part of the
squeegee.
3. Take off the rubber holder blade.
4. Replace the front rubber.
5. Reassemble all parts.
SQUEEGEE "V" TYPE (OPTIONAL): FRONT RUBBER
REPLACEMENT
Check the squeegee rubber wear and eventually re-
place it.
For the replacement it is necessary to:
1. Disassemble the squeegee from the support as
indicated under "SQUEEGEE CLEANING".
2. Unscrew the tie rods (1) on the terminals (2) of
the rubber holder blade and disengage the terminals.
3. Unscrew all wing nuts (6) and take off the rubber
holder blade (7).
4. Take off the rubber (8) and replace it.
To reassemble the squeegee repeat reverse the oper-
ations above mentioned, inserting first the rubber (8)
into its guides, then positioning the rubber holder
blade and finally screwing down all wing nuts and
the tie rods of the two terminals.
GB