Floor Cleaning; Connection Of The Batteries To The Machine; Recovery Tank; Detergent Solution Tank - Floorpul amber 66 24v Manual De Uso Y Mantenimiento

GB
ATTENTION:
Use only brushes supplied with the machine or the
ones indicated in the paragraph "RECOMMENDED
BRUSHES". The use of other brushes can compromise
security.

FLOOR CLEANING

CONNECTION OF THE BATTERIES TO THE MA-
CHINE
Once that the battery recharging has been complet-
ed:
1. Disconnect the connector (3) of the battery re-
charger (1). To do this, it is necessary to reach the
battery compartment as indicated under paragraph
"ACCESS TO THE BATTERY COMPARTMENT".
2. Connect instead the machine connector (2).
3. Close the battery compartment.

RECOVERY TANK

Check that the cover of the suction filter (1) is cor-
rectly secured, after rotating the levers (2) and that
the suction motor hose (3) is correctly connected to
it.
Verify also that the squeegee hose couplings (4) are
correctly inserted into the seats, that the exhaust
hose plug (5) placed in the front part of the machine
is closed and that also the inspection cap (6) is
closed well.

DETERGENT SOLUTION TANK

The capacity of the detergent solution tank is indi-
cated in the technical data.
Open the screw plug placed in the rear left part of
the machine and fill the detergent solution tank
with clean water at a maximum temperature of 50°C.
Add the liquid detergent in the percentage and con-
ditions foreseen by the manufacturer. To avoid ex-
cessive foam presence, which could cause problems
to the suction motor, use the minimum percentage
of detergent. Screw down the plug to close the tank.
ATTENTION:
Use always low foam detergent. To avoid foam pres-
ence, before starting working operation, introduce
into the recovery tank a minimum quantity of anti-
foam product.
Never use pure acid.
3S SYSTEM "SOLUTION SAVING SYSTEM" (OP-
TIONAL)
The need of an increasing carefulness to the envi-
ronment, and to the abuse of polluting elements,
such as detergents in the floor cleaning machines,
has brought us to the realization of a device which,
regardless from the capacity to use the machine by
the operator, keeps the minimum flow of the deter-
gent solution constant, having been properly cali-
brated by an expert technician. The best detergent
solution amount with this system will be the one
which realizes the minimum flow of detergent solu-
tion sufficient to clean correctly the floor. For this
reason the system is called "Solution Saving System"
abbreviated to "3S" system.
The system is composed by a hydraulic circuit paral-
lel to the traditional one which can be enabled or
disabled directly from the instrument board through
a 3-position switch with the following functions:
(1) = Position solution valve with traditional func-
tioning with variable water flow that differs by the
opening of the solution valve.
(2) = Position STOP with functioning without flow
(drying only).
(3) = Position 3S with functioning with optimal
fixed flow.
24

STARTING OF THE MACHINE

1. Turn the key (9) clockwise.
2. Check the battery type and the charge level on
the display (1).
3. Press the brushes motor switch (6).
4. Press the suction motor switch (3).
5. Press the solenoid valve switch (5).
6. Lower the brushes base onto the floor.
The machines which have the brushes base lifting
with the manual hydraulic pump, push downwards
the small lever of the valve control (1).
The machines which have the electrical brushes base
lifting press the push button (7) of up/down of the
brushes base.
7. Acting upon the solution valve lever (14) open
and adjust the detergent solution flow.
The water starts to flow automatically acting upon
the levers drive control (12). On the instrument
board the indicator of the solenoid valve switch (5)
will turn on. Releasing these levers, the flow will stop.
Models equipped with the 3S system (optional), it is
necessary to press the suitable switch to activate the
detergent solution supply by choosing between the
traditional adjustment system through the solution
valve or the system of fixed optimum supply (see
under "3S SYSTEM SOLUTION SAVING SYSTEM").
8. Acting upon the squeegee lifting lever (17) lower
the squeegee.
9. Acting upon the levers drive control (12) the ma-
chine starts to move, the brushes start to rotate and
the squeegee starts to dry.
10. During the first metres check that the squeegee
adjustment guarantees a perfect drying action and
that the detergent solution flow is appropriate. It
has to be sufficient to wet the floor uniformly avoid-
ing the leakage of detergent from the splash guards.
Always consider that the correct quantity of solution
detergent depends on type of floor, dirtiness and
machine speed.

FORWARD MOVEMENT

The traction of the machine is given through an
electronically controlled motor.
To move the machine, act upon the key (9) and then
rotate the levers drive control (12) placed on the
handle bar, in forward you obtain the forward drive,
in reverse the backwards movement is obtained. The
control acts in a progressive way, therefore it is pos-
sible to graduate the speed depending on each re-
GB