Cleaning, Maintenance And Ordering Of Spare Parts - HERKULES ZGS 3300 UG Manual De Instrucciones

Anleitung_ZGS_3300_UG_SPK7:_
machine head to rise slowly, applying slight
counterpressure as it does so.
7.5 Crosscut 90° and turntable 0°- 45° (Fig. 9)
The crosscut saw can be used to make right and left
angular cuts of 0°- 45° in relation to the stop rail.
Using the handle (10), set the turntable (8) to the
desired angle, i.e. the scale pointer (11) on the
turntable must coincide with the desired angular
setting on the stationary base plate (8).
Retighten the locking grip (10) to secure the
turntable (8) in place.
Make the cut as described in section 7.4.
7.6 Miter cut 0°- 45° and turntable 0° (Fig. 10/12)
The crosscut saw can be used to make miter cuts of
0° - 45° in relation to the work face.
Move the machine head (4) to its upper position.
Fasten the turntable (8) in 0° position.
Undo the clamping lever (13) and use the handle
(2) to tilt the machine head (4) to the left until the
pointer (23) coincides with the required angle
value (15).
Retighten the clamping lever (13) and make the
cut as described in section 7.4.
7.7 Miter cut 0°- 45° and turntable 0°- 45° (Fig. 11)
The crosscut saw can be used to make miter cuts to
the left of 0°- 45° in relation to the work face and, at
the same time, 0° - 45° in relation to the stop rail
(double miter cut).
Move the machine head (4) to its upper position.
Release the turntable (8) by slackening the
locking grip (10).
Use the handle (10) to adjust the turntable (8) to
the angle required (in this connection see also
section 7.5).
Retighten the locking grip (10) in order to secure
the turntable in place.
Undo the locknut (13) and use the handle (2) to
tilt the machine head (4) to the left until it
coincides with the required angle value (in this
connection see also section 7.5).
Retighten the locknut (13). Cut as described
under section 7.4.
7.8 Changing the saw blade (Fig. 13)
Pull out the power plug.
Swing up the machine head (4).
Swing up the adjustable blade guard (6).
Press the saw shaft lock (17) with one hand while
holding the wrench (32) on the flange bolt (25)
with the other.
Firmly press on the saw shaft lock (17) and
slowly rotate the flange bolt (25) in clockwise
direction. The saw shaft lock engages after no
27.04.2011 11:22 Uhr Seite 13
more than one rotation.
Now, using a little more force, slacken the flange
bolt (25) in clockwise direction.
Turn the flange bolt (25) until it is completely
removed.
Take the blade (5) off of the inner flange and pull
out.
Mount and fasten the new blade in reverse order.
Important! The cutting angle of the teeth (i.e. the
direction of rotation of the saw blade) must
coincide with the direction of the arrow on the
housing.
The blade flanges must be thoroughly cleaned
prior to mounting the blade.
Reattach the movable blade guard (6) in reverse
order.
Ensure that the saw shaft lock (17) is slackened.
Check to make sure that all safety devices are
properly mounted and in good working condition
before you begin working with the saw again.
Important: Every time that you change the saw
blade, check to see that it spins freely in the
groove of the turntable in both perpendicular and
45° angle settings.
7.9 Carrying the saw
Release the miter engagement button (10) and
turn the table all the way to the right. Lock the
table at a miter angle of 45°.
Pull the cutting head forward and lock the slide.
Lower the cutting head and press in the locking
button (16).
Carry the crosscut and miter box saw by its
integral carry-handle (31) and the side of the
base.
8. Cleaning, maintenance and ordering
of spare parts
Always pull out the mains power plug before starting
any cleaning work.
8.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the device
immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts
of the equipment. Ensure that no water can seep
into the device.
GB
13