Faucet Installation (10-0189); Below Counter Non-Espring Faucet Installation (11-0720) - Amway eSpring Manual Del Propietário

BELOW COUNTER NON-eSpring
FAUCET INSTALLATION (11-0720)
REVIEW ALL INSTRUCTIONS IN THE PURCHASED NON-eSpring FAUCET OR DISPENS-
ING DEVICE TO BE SURE YOU HAVE ALL PARTS AND TOOLS PRIOR TO INSTALLATION.
1. Install Auxiliary Faucet or Dispensing Device according to manufacturer's
instructions.
2. Follow preparation steps for any faucet or dispensing device on p. 3.
3. Review bag labeled CXV3645,
which contains components
used with NON-eSpring instal-
lations (Fig. 26).
a. Supply Connector
b. Pressure Regulator
c. Inlet Tubing
d. Outlet Tubing
e. Tubing Removal Tool
f. T Connector
g. Tubing Reducer Connector
* Faucet not included
4. a) Lay the red tube from the Pressure Regulator Assembly on the top of the
diagram, and lay the blue tube on the bottom. Use a pen to mark them at
the arrows (Fig. 27). (These ends will connect to the Water Purifier).
b) Lay the unmarked end of the blue tubing on the top of the diagram and
mark a line at ¾" (18 mm). (Fig. 27).
c) Lay the tube from the cold water supply on the top of the diagram and
mark a line at ¾" (18mm) or at arrow (Fig. 27).
Fig. 27
5. Remove the Top Shroud from the Water
Purifier . Remove the Electronic
Module (Fig. 28).
6. Connect the tube from the cold water
supply to the screen side of the Supply
Connector on Pressure Regulator
Assembly . Arrow in balloon shows
water flow direction (Fig. 29).
NOTE: The supplied components (Fig. 29)
must be used between the valve at the water
supply and the eSpring Water Purifier.
1035793_eng.indd 5
Fig. 26
b
a
c
d
f
e
g
⁄ "
3
4
( )
⁄ " ( )
5
8
Fig. 28
Fig. 29
7. Insert the RED tube from the Pres-
®
sure Regulator Assembly into the
large port on the Bracket. Insert the
end of the BLUE tube marked at 5/8"
(15 mm) into the small port on the
Bracket (Fig. 30).
NOTE: You will feel resistance before the
tubes are fully installed. Ensure the tube is
fully pushed in until it meets the mark or
the marks disappear, as a check on each of
the tube connections in steps 7 and 8.
8. The other end of the BLUE tube
marked at ¾" (18mm) connects to
the NON-eSpring Faucet or dispens-
ing device by inserting BLUE tube
into the Tubing Reducer Connector.
Follow manufacturer's installation
instructions to connect the other
end of the connector to the faucet
or dispensing device (Fig. 31A).
NOTE: For installation with refrigerator
or secondary device use the T Connector
in place of the Tubing Reducer Connector
(Fig 31B).
9. Open the NON-eSpring Faucet or dispensing device
supply shut-off valve to start water flowing through the Water Treat-
ment System (Fig. 32).
NOTE: It will take a short time for water to saturate the Cartridge and flow from
the Diverter. Flush for a minimum of 5 U.S. gallons (20 liters) (approximately
5-15 minutes) to remove air pockets and carbon dust. If water is not clear, see
Troubleshotting, p. 8.
10. Turn off the NON-eSpring Faucet or dispensing device and check for any
signs of leakage at all tubing connections
or bubbling, refer to Troubleshooting, p. 7.
11. Skip to COMPLETING THE INSTALLATION, p. 10.
Residents of Massachusetts, please adhere to the State of Massachusetts
Plumbing Codes. Use a licensed plumber for installation.
Fig. 30
*
Fig. 31A
*
Fig. 31B
. Open the water
(Fig. 32). If there is leaking
*
*
Fig. 32
6/10/14 4:42 PM
5