Parc-100 / Rgb; Operation; Independent Operation; Colour Spotlight And Stroboscope - IMG STAGELINE ODC-100/ RGB Manual De Instrucciones

2) On the last spotlight, screw the protective
cover supplied onto the inline jack of the
cable POWER OUT. The cable carries mains
voltage!
3) Connect the mains plug of the first spotlight
to a mains socket (230 V~ / 50 Hz).

3.3.2 PARC-100 / RGB

For power supply, the unit is equipped with
Powercon ® connections.
CAUTION! Never connect or disconnect a Pow-
ercon plug while voltage is applied. Always
make the Powercon connection before making
the mains connection. When disconnecting,
always disconnect the mains connection before
disconnecting the Powercon connection.
Connect the mains jack POWER IN to a mains
socket (230 V~ / 50 Hz) via the mains cable pro-
vided. Connect the blue Powercon plug of the
cable to the mains jack, and then turn the plug
clockwise until it locks. To remove the plug, pull
back the safety latch of the plug and turn the
plug counter-clockwise.
Power supply of multiple
PARC-100 / RGB spotlights
If multiple PARC-100 / RGB spotlights are used,
the jack POWER OUT of the first spotlight can
be connected to the mains jack POWER IN of
the second spotlight. For this, a mains cable
with Powercon plugs (NAC-3FCB and NAC-
3FCA) is required. Proceed in the same way to
connect the second spotlight to the third spot-
light etc. until all spotlights have been connected
in a chain. Thus, up to 19 spotlights can be inter-
connected. The jack POWER OUT can also be
used for power supply of other (light effect)
units.
CAUTION! To reduce the risk of fire caused by
overload, the current load of the cables and the
mains plug must not exceed 10 A.

4 Operation

The operating modes and the setting functions
are selected via a menu by means of the buttons
MENU, ENTER, UP and DOWN. Figure 12 on
pages
78 and 79
modes and functions via the menu and the indi-
cations on the display.
16
shows the selection of the

4.1 Independent operation

4.1.1 Colour spotlight and stroboscope

In this mode, the spotlight constantly radiates
light of an adjustable colour. In addition, the stro-
boscope function is available.
1) Press the button MENU repeatedly until the
highest menu level has been reached (on the
very left in the menu structure on pages
).
and 79
2) Press the button UP or DOWN repeatedly
until the display indicates
3) Press the button ENTER. The display now
indicates , , or
= brightness of the colour red (0 – 255)
= brightness of the colour green (0 – 255)
= brightness of the colour blue (0 – 255)
= flash rate (0 – 20) of the stroboscope
4) Use the button ENTER to select the four set-
ting options one after the other, and use the
button UP or DOWN to set the brightness or
flash rate.
Note: Setting the brightness of the colours red,
green and blue will not only change their bright-
ness but also the shade of colour in case the
colours are mixed. Therefore, first set the colour
which is to dominate to the desired brightness
and then add the other two colours. If the
intended colour mixture is white, first set the
brightness of the green colour because it appears
as the brightest colour to the human eye. Then
add red to result in yellow and finally add blue to
result in white.
Important: Do not exit the menu item for a
colour or the flash rate with the button MENU
before switching off the spotlight. If you do, the
spotlight will remain dark when you switch it on
again.
4.1.2 Different shades of white
Storing 11 shades of colour
In this mode, the spotlight radiates white light.
11 different shades of white are stored which,
however, can be changed. For each shade of
white, the colours red, green and blue can be set
to a different brightness so that this mode can
also be used to store 11 individual shades of
colour.
1) Press the button MENU repeatedly until the
highest menu level has been reached (on the
78
.
and a number.